Tools

After foutrty years in the saddles of Harley-Davidsons, on long hauls, short trips and race tracks, eventually, we have compiled a tool set, which is the must-have combination to perform routine maintenance works and on-the-road emergency repairs. Even on our journey through Patagonia (www.wwag.com/About us/Wrecking Crew) the PanAm Tool Kit was, basically unchanged, part of the equipment we had stashed into the saddlebags. Chain tensioning (primary and secondary), plug changes, oil change, points ignition timing, valve adjusting - for any job, which naturally occurs during long trips, there is exactly the right tool. No compromises. This also counts for quality, because every single component of this kit is a class A tool by the German manufacturers GearWrench, Stahlwille, Walter, Knipex or Felo. Admittedly, this ends up a bit more expensive but, on the other hand, this kit is a once-in-a-liftime purchase. A super heavy duty canvas roll holds all parts securely and rattle-free in place. In case of loss all single components are available separately.

After fourty years in the saddles of Harley-Davidsons, on long hauls, short trips and race tracks, eventually, we have compiled a tool set, which is the must-have combination to perform routine maintenance works and on-the-road emergency repairs. Even on our journey through Patagonia (www.wwag.com/About us/Wrecking Crew) the PanAm Tool Kit was, basically unchanged, part of the equipment we had stashed into the saddlebags. Chain tensioning (primary and secondary), plug changes, oil change, points ignition timing, valve adjusting - for any job, which naturally occurs during long trips, there is exactly the right tool. No compromises. This also counts for quality, because every single component of this kit is a class A tool by renowned manufacturers like Bahco, Walter or Knipex. Admittedly, this ends up a bit more expensive but, on the other hand, this kit is a once-in-a-liftime purchase. A super heavy duty Cordura or canvas roll holds all parts securely and rattle-free in place. In case of loss all single components are available separately.

The rugged PanAm tool roll is also available empty for those who prefer to equip it with their own tools.

If it’s rumbling down Interstate 8 to the beach or riding with your Knuckle, Panhead or Shovel ridin’ buddies to your favourite lake in the mountains: even the best cared for Harley, once it has more than 4 or 5 decades on the odometer, every now and then can surprise you with a show-stopping mechanical gremlin, resulting in an unwanted stop by the roadside. So, what do you do, call a tow truck?

Naw. Better to have a tool roll on board with exactly the right assortment of wrenches, pliers, screwdrivers and small parts to get your chopper going again.

That’s why we put together the tool-roll-to-end-all-tool-rolls, filled with over 40 years experience of riding this world’s roads and the knowledge that comes with it; one that really earns the name "Roadside Companion".

Inside you’ll find open ended wrenches in different sizes, an adjustable wrench, a plier wrench, screwdrivers, a test lamp, wire brush, spark plug socket, jumper wire. Added to that an assortment of nuts, bolts, washers, lockwashers, hose clamps, safety wire, zip ties, insulating tape, cotter pins and a clevis pin.

All this has been wrapped up in some heavy gauge (405 g/m²) oiled cotton canvas sourced from the UK. It comes with a GOTS (Global Organic Textile Standard) certificate and has a fold-out flap to keep your knees clean and your small parts from disappearing into the underbrush. Heavy Swedish made leather straps hold everything together.

This breakdown relief kit is insurance against technical issues that can stay in your saddle bags at all times. It also serves as a basic workshop starter set for those who are new to riding old hogs. Plus you get the chance to provide help to other riders in a bind, thus making you a true roadside companion yourself.

The tool kit »I-8 Roadside Companion« by PanAm is optimized for pre 1969 Harley models with distributor or magneto ignition.

Packing list (no guarantee, may be subject to short term changes:)
Bahco open end wrenches 1/4”x 5/16”, Bahco open end wrenches 3/8” x 7/16”, Bahco open end wrenches 1/2” x 9/16”, Knipex pliers wrenches , adjustable open end wrench, 3 screwdriver: 1 x exchangeable blade, flat and Philips, straight; 1 x L-shape, flat, by Bahco; 1 x L-shape, Philips, by Bahco, Walter test lamp, Walter wire brush, Insulating tape, Bypass wire, PanAm spark plug wrench, cotton bags with selected small parts in several common sizes: screws, nuts, washers, lock washers, hose clamps, wire, cable ties, cotter pins, clevis pins.,

Reproductions of the tool boxes for most models thru 1934.

Reproductions of the rectangular tool boxes as used 1936–39 and the teardrop style tool box used 1940–59. Perfect for restorations or as a useful accessory on custom bikes. These tool boxes feature a stock style key lock.

The AccuMATE 6/12 is a versatile, automatic charger and maintainer for all modern and classic 6 & 12V lead-acid and gel-electrolyte type batteries. It will charge and maintain batteries of capacity up to about 75Ah. Also ideal for long term maintenance of the batteries of irregularly or seasonally used vehicles and vintage & collectors vehicles.

Sturdy test lamp to examine circuits in your lighting and ignition systems. Applicable for 6 to 24 V. Comes with protective screw-on cap, 70 cm lead and alligator clip.

Duplicate of the original tool used to remove and install OEM-type air cooled spark plugs with 1-1/8” (28.5 mm) hex.

High quality stand for truing and balancing wheels. Equipped with bubble level, height adjustable control needle, adjustable legs as well as two adjustable centering points for accurate clamping of the wheel. A 12mm shaft with clamping cones runs on two ball bearing double rollers, to allow friction free movement of the shaft while balancing the wheel.

Reproduction of the classic facory tool.

Reproduction of the proven factory tool.

For six different nipple sizes. Professional quality.

Classic Harleys well into the 1960s feature lots of slotted screws on engine, transmisison, primary etc. which you don´t want to tighten or loosen with a cheap screwdriver. It will mar the slots in no time and make you look a poor mechanic. This special edition The Cyclery screwdriver set includes the exact size screwdriver for most slotted screws you find on older H-D models. They feature hollow ground tips to perfectly fit the respective slot, avoiding damages and keeping your expensive hardware in good shape. The square shanked blades are hardened to R/C 52-56 and are guaranteed not to twist or chip. The handles are turned from Maine hardwood and protected with a nicely stained finish and a nickel plated steel ferrule. A quality wooden handle is key to a good grip with hands becoming slippery from oil and these screwdrivers provide that great wood handle feel that only gets better with time. Classy tools for classic bikes - an ideal combination.
The 6-piece set comprises the following blade sizes:
#1 = 1.0 x 4.7 x 160 mm, #2 = 1.0 x 6.0 x 183 mm, #3 = 1.2 x 6.0 x 205 mm, #4 = 1.3 x 7.0 x 209 mm, #5 = 1.4 x 9.3 x 168 mm, #6 = 1.7 x 9.3 x 272 mm,

Factory style open end wrenches for the large manifold plumber nuts.

Engines with a leaking intake manifold are hard to kickstart and will never run properly. That’s why you need one of these leak testers in your workshop, which will once and for all take the guess work out of your installation job. Just bolt them to your manifold (use the stock gasket!), close both intake valves, by slowly turning the engine and with an air hose hooked-up to the G 1/4” fitting apply up to 10 psi of pressure. Spray soapy water around the gasket and manifold clamps and in case of appearing bubbles you can clearly spot any air leaks in your intake system.

To install the pinion shaft bushing OEM# 413-15 and to drill the dowel pin hole to the factory location.

The multipurpose degree wheel can be used to perform ignition timing, crankcase breather timing, cam degreeing etc.. The wheel is designed to adapt to the sprocket shaft of any Big Twin or Sportster by simply using the correct adapter provided. A must for every well equipped engine builder´s shop.

Tool for lapping rod races to precise tolerances. Each set includes 1 x 1 1/2” lap head, 1 x 1 5/8” lap head and 1 x shaft.

Many ioe engines idle irregularly or start badly due to a leaking intake housing/cylinder joint. This professional lapping tool cures this problem. The kit consists of 2 lapping heads and 1 lapping disc which allow to reface the respective surfaces of 1000cc and 1200cc engines.

Multi-part pro tool to remove and install exhaust valves on IOE models.

Use to tighten or loosen exhaust pipe nuts. Works with 1200cc models 1921-up and 1000cc models 1925-up.

To remove and install tranny case countershaft bushings and the main drive gear bearing race of all 3-speed transmissions 1916→.

The compression screw features an extremely durable heat-treated steel tip to press out chain pins. However, we recommend the side pin heads to be ground off flush.

Great little tool used to press on the side plates of chain links. Especially recommended for O-ring chains. Solid tool steel.

This handy tool pulls chain ends together for easy chain link installation.

Exactly the tool you always wished you had when it comes to replacing the worn sprocket on your rear brake drum. Clamped in a vise it holds the brake drum and supports the rivet head while you peen over the shank. Comes with rivet puller plus head maker, drum collar and spacer (for K/XL drums). This equipemnt will definitely make your workshop life a lot easier.