

>

Shop

>

Parts for Pre War Harley-Davidson

>

Electrical



Electrical

The Cyclery Switch Assembly Brackets

The Cyclery Switch Assembly Brackets

Authentic duplicate of the lower support bracket for the switch assembly/dash.

Switch Assembly Mounting Bolts

Switch Assembly Mounting Bolts

Authentic duplicates of the switch assembly fastening bolts.

The Cyclery Replacement Parts for Switch Assemblies 1926-1937

The Cyclery Replacement Parts for Switch Assemblies 1926-1937

Vintage Button Switch

Vintage Button Switch

Reproduction of the accessory horn and magneto kill switch.

Toggle Switches →1973

Toggle Switches →1973

Handlebar mount switches that require routing of wires inside the handlebars.

Button Switches 1926-1971

Button Switches 1926-1971

Stock replacement button switches for horn and starter activation. The selection includes the early, low profile single wire button and the higher 1953→ double wire version. This later version provides a separate ground wire, whereas the early version relies on ground via the housing.

Generator End Covers 1918-1932

Generator End Covers 1918-1932

Accurate, year specific reproductions of the generator end covers for IOE models.

Generator Brushes 1926-1931

Generator Brushes 1926-1931

This kit comprises all three brushes with springs for early H-D generators. The large brushes fit 1926-1931 Twins and 1932-1934 Singles. The small brush fits alll models 1926-1957.

32E Type Generator 6V

32E Type Generator 6V

The 6 V originals: the generators offered here are professionally rebuilt original units, adjusted, dyno-tested and ready-to-install.

32E Type Generator 12V

32E Type Generator 12V

For those who do not insist on 100% authenticity. These 32E generators are updated with special fields and armatures to produce 12V for an improved lighting efficiency. Consequently they require a suitable 12 V battery, regulator, coil and bulbs.
The generators offered here are professionally rebuilt original units, dyno-tested and ready-to-install.

Delco Relay Style Regulator 6V

Delco Relay Style Regulator 6V

When upgrading your old hog with a more powerful 2-brush generator there is always the problem, where to mount the larger regulator that is required with them. Here is an easy solution: a fully electronic regulator which mounts at the same spot as your early cut-out relay and which even fits under your small Delco Remy cover. Problem solved.

Delco Relay Style Regulator 12V

Delco Relay Style Regulator 12V

Designed to fit in the place of your Delco Remy cut-out relay when you have installed a later 12V type 65A generator, a 32TC or when the 32E generator has been converted to 12V. Accepts the Delco Remy tin cover.

The Cyclery Battery Boxes for J/JD Models

The Cyclery Battery Boxes for J/JD Models

Nicely and accurately made reproductions of the battery boxes and covers for generator equipped J/JD models.

The Cyclery Battery Boxes for V Models

The Cyclery Battery Boxes for V Models

Nicely made and accurate reproductions of the battery boxes and covers for V-series models.

Replacement Parts for Battery Box for V Models

Replacement Parts for Battery Box for V Models

Main Wiring Harness Kits

Main Wiring Harness Kits

Perfect reproductions of the original Harley wiring harness kits. The wiring kits for models up to 1969 feature cotton braided insulation and asphalt looms just like the original, for models 1970-up the wires are PVC covered with vinyl looms. The color-code of the wires duplicates stock. Harnesses thru 1969 include handlebar and taillight wires.

Accurate reproduction of the frame clamp with terminal plate as used on 1928-1929 twins to connect the tail lamp wire.

Wire terminals for Headlamp, Horn & Spotlights

Wire terminals for Headlamp, Horn & Spotlights

Accurate reproduction of insulators and hardware for the headlamp/horn bracket on all models 1945-1957 with Springer forks.

Terminal Plates and Boxes

Terminal Plates and Boxes

Detailed reproduction of the terminal boxes found on Big Twins and 45” from 1948 to 1977 and the triple-tree mounted terminal board, which was stock  on all FL models from 1949-1969.

Reproductions of the original spring steel clips which help to accurately route the stock wiring harness.

Accurate reproductions of the stock terminal posts as used on models thru 1947.

Woven cotton loom with black bituminous coating. A must for the perfect restauration of the wiring harness on antique bikes.

Electric Wires Cotton Braided

Electric Wires Cotton Braided

For the repair or custom fabrication of cloth covered wiring harness kits as used on classic Harleys and Indians.

Klaxon-11 Horns

Klaxon-11 Horns

Good reproduction of the original Klaxon-11 horns which was factory equipment on all electrical models 1920-1930. While it looks externally just like the factory part it houses a modern electric horn inside.

Mounting Brackets for Klaxon Horn

Mounting Brackets for Klaxon Horn

Reproductions of the stock mounting brackets for Klaxon horns. Nuts and bolts are not included.

Bosch Type Horn

Bosch Type Horn

Accurate reproduction of the German horn as used in the 1920’s and 1930’s.

Noris Type Horn

Noris Type Horn

Accurate reproduction of the German horn as used in the 1920’s and 1930’s.

Strange Bird Ignition Switch Covers for Switches →1993

Strange Bird Ignition Switch Covers for Switches →1993

Introduced on 1936 OHV models, these ignition switch covers were factory standard on Big Twins 1937-1948, but can also be used on dash board mounted ignition switches →1993.

CMS Stoplight Switches 1934-1938

CMS Stoplight Switches 1934-1938

Reproductions of the stop light switches and brackets as used by the factory during the 1934-1938 model years.

CMS Stoplight Switch Chain and Spring 1934-1938

CMS Stoplight Switch Chain and Spring 1934-1938

Reproductions of the chain and spring for the 1934-1938 stop light switches.

The Cyclery Stoplight Switch Lever 1934-1936 V-Series Models

The Cyclery Stoplight Switch Lever 1934-1936 V-Series Models

Reproduction of the activating lever for the 1934-1936 V-series stop light switches. Mounts behind the nut of the rear brake crossover shaft.

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com