Shop Fork
Classic Springer Forks

Classic Springer Forks

The Cyclery Classic Springer Forks
The Cyclery Classic Springer Forks
Complete and accurate reproduction of the classic H-D Springer fork (Inline) as used by the factory on Big Twins 1937-1938. Manufactured just like back in the good old times, i.e. with forged legs and connecting components, which makes them equal to the original counterpart concerning stability and service life.
Use this top-quality fork as stock replacement for your restauration or as a part of your chopper or bobber project-bike. The special features are:
Bare - allows an individual finish of the fork, Narrow 1936-1937 type mudguard mount , Completely brazed, Brake anchor mount for drum brake are soldered just like stock, "Swept-forward" rigid fork as used by the factory 1936-1940, Rockers are round at the top, i.e. they have no raised sprues for the grease nipples, Grease nipples for the guide bushings on the upper triple clamp point inwards, as common in 1936-1938, Threaded hole on the rigid fork for the brake control coil clip is slightly off-center as it was fitted from late 1937 onwards , The dimensions of our standard forks are exactly the same as for the original Springer forks (48,5 cm = 19” from center of wheel axle to lower neck bearing seat).,
This fork features a fork stem that works with the included centering collar for 1936-up ball bearings. It is not drilled for the 1948→ steering head lock.
Length is measured from axle center line to seat of lower steering head bearing.
more …
Cannonball I-Beam Springer Forks
Cannonball I-Beam Springer Forks
Once upon a time when there weren’t any custom parts you could buy from your local shop, the VL fork was a very popular item because it made your Knuckle or Panhead bobber different from the next guy’s scooter. Besides you gained half an inch of length compared to 1936-up Springer forks for improved ground clearance and a more stretched look. Now it’s time to revive those days of the golden 40’s and 50’s with the Cannonball version of H-D’s VL type fork.
Manufactured just like the original, which means I-beams and connecting braces are drop forged on a huge 10 meter forge hammer. This is the only procedure that guarantees these components stand up to the job.
The problems with installing the OEM fork were the large fork stem and the handlebar mounting so the Cannonball fork is modified here. It features a Ø1” fork stem that works with the centering collar (available seperately) for 1936-up ball bearings. Moreover the stem also features two Ø1” bearing seats for the use of Big Twin tapered roller bearings without any modifications. The leg tops accept the 36-up Springer inline handlebars. This makes installation a snap compared to the original counterpart.
Certificate of stability for 4-speed Big Twins thru 1986. Length is measured from axle center line to seat of lower steering head bearing.
Although these Custom forks are intended for 1936-1957 rigid frame Big Twins they can be mounted with later frames, too, provided you have/install matching frame head bearings. The builder has to consider rake, trail, overall chassis geometry, brake function, etc.
more …
Classic Springer Forks
Classic Springer Forks
Complete and accurate reproduction of the classic H-D Springer fork as used by the factory on Big Twins 1936-49 and on 45” models from 1941–57. Manufactured just like back in the good old times, i.e. with forged legs and connecting components, which makes them equal to the original counterpart concerning stability and service life.
Use these top-quality forks as stock replacement for your restauration or as a part of your chopper or bobber project-bike.
All brackets for brake anchor, front fender and ride control are there and just like stock., The dimensions of our standard forks are exactly the same as for the original Springer forks (48,5 cm = 19” from center of wheel axle to lower neck bearing seat)., The "Builder" versions come unassembled with bare rigid and spring forks, chrome or black springs and black rockers.,
Length is measured from axle center line to seat of lower steering head bearing.
more …
Classic Springer Forks 2” Shorter than Stock
Classic Springer Forks 2” Shorter than Stock
These are the Inline Springer forks for cool Lowrider projects. They are 2” shorter than the stock versions and will let your bike’s front end look a lot different. All other features match the standard length Classic Springer forks:
all brackets for brake anchor, front fender and ride control are there and just like stock., fork stem works with the centering collar (available seperately) for 1936-up ball bearings and also features two Ø1” bearing seats for the use of 1949-up tapered bearings without any modifications. They are not drilled for the 1948→ steering head lock.,
Length is measured from axle center line to seat of lower steering head bearing.
Although these Custom forks are intended for 1936-1957 rigid frame Big Twins they can be mounted with later frames, too, provided you have/install matching frame head beariings. The builder has to consider rake, trail, overall chassis geometry, brake function, etc.
more …
Classic Springer Forks 2” and 4” Longer than Stock
Classic Springer Forks 2” and 4” Longer than Stock
Extended Springer forks which provide more ground clearance when building bikes with larger than stock neck rakes. Actually, the +2” versions were factory equipment on XA and 1941 WLA military models. Made with forged legs, just like the shorter versions. They feature a fork stem with two Ø1” bearing seats for the use of 1949-up tapered roller bearings without any modifications.
Length is measured from axle center line to seat of lower steering head bearing.
Although these Custom forks are intended for 1936-1957 rigid frame Big Twins they can be mounted with later frames, too, provided you have/install matching frame head beariings. The builder has to consider rake, trail, overall chassis geometry, brake function, etc.
more …
Classic Springer Forks ≥8” Longer than Stock
Classic Springer Forks ≥8” Longer than Stock
A literally indispensable component for Old School choppers is an extended Springer fork which until today was a major obstacle because you either had to cut and extend your stock fork (ouch!) or purchase one of those somewhat flimsy aftermarket springer forks. Nowadays, there are professional solutions and the Big Twin forks offered here feature one-piece, forged tubes for strength and safety, made just like the shorter versions.
Feature a fork stem with two Ø1” bearing seats for the use of 1949-up tapered roller bearings without any modifications., With a positive rake, i.e. the steering stem is inclined to the front by 3°. This is done to avoid a steering neck so high and inclined that the bike is impossible to steer. We call these forks Offset +3°, according to their rake., Standard rockers limit fork travel on overlength forks so the 16” versions sport special longer rockers to maintain proper travel. They accept 19 mm axles for custom brake and wheel installation.,
Length is measured from axle center line to seat of lower steering head bearing.
Although these Custom forks are intended for 1936-1957 rigid frame Big Twins they can be mounted with later frames, too, provided you have/install matching frame head beariings. The builder has to consider rake, trail, overall chassis geometry, brake function, etc.
more …
Rigid and Spring Forks for Classic Springer Forks
Rigid and Spring Forks for Classic Springer Forks
Reproductions of the rigid and spring forks for Classic Springer forks. The 1936-early 1938 rigid forks feature inside, forward facing grease fittings and a brazed brake anchor tab. The late 1938-1940 rigid forks feature outside facing grease nipples, also with brazed brake anchor tab. Both versions have correct forward swept fork legs. This is not the case with later 1941→ rigid forks, which have the lower rocker stud hole inline/centered with the fork’s top end.
more …
Rigid and Spring Forks for Cannonball I-Beam Springer Fork
Rigid and Spring Forks for Cannonball I-Beam Springer Fork
Raw, unpainted rigid and spring forks for those who would like to assemble their personal Cannonball I-Beam Springer fork from individual parts.
more …
Accessories
Accessories
Replacement Parts
Replacement Parts

Related Topics

Classic Springer Fork

Introduced on the Knucklehead in 1936, it was used on Big Twins from 1937 to 1949. On 45"/750cc flatheads, the classic Springer fork was used from 1941-1957. Compared to the previous I-Beam forks, the legs of the rigid fork were no longer drop forged, but were made of oval tubes. We keep hearing that this was for cost reasons, but as we know from our own experience, the manufacturing process for such oval, tapered and also S-shaped tubes is at least as costly. However, the connection to the lower triple clamp can be soldered/welded. On the I-Beam forks, it is riveted.

A little technology

The suspension travel of Springer forks is not all that great, the compression travel is about 50 mm. However, Springer forks respond as fine as telescopic forks, with proper adjustment of the spring tension. Springer forks were not damped in standard form, but there were - and are - friction dampers or hydraulic dampers as accessories. Handlebar slap was prevented with a factory-installed steering friction damper.

Our range of Springer forks

For both custom bikes and replacement of hard to find original parts, we offer a wide selection. Springer forks as original replacement for Big Twins, 45"/750cc Solo flatheads, Servi-Cars, Springer forks with overlength or underlength and also individual rigid and spring forks. Additionally, we offer a version of the I-Beam Springer Fork for Big Twin models 1936 and up. It is equipped with a 1" neck stem and fits, in combination with the supplied centering ring, for ball bearings from 1936 on. Two inch bearing locations allow mounting with taper roller bearings and the leg tube ends fit for in-line Springer handlebars from 1936 onwards.

Also included are replacement parts and accessories such as fork springs, rocker kits, grease nipples, repair bushings, adjusting nuts, triple clamps and the various shocks. For people who can solder or weld, there are also fork stems, fork legs and brake anchor mounts.

What does inline mean? What does offset mean on a Springer fork?

Harley-Davidson used different steering head angles on the frames of the 1000 and 1200 OHV Twins and the 1200 and 1300 SV engines over the 12 year period they were built:

  • 1936-1937: 25°
  • 1938-1940: 28°
  • 1941-1945: 29°
  • 1946-1948: 30°

For the riding charcteristics this means that - if the fork remains the same - the caster becomes larger and larger. The motorcycle becomes directionally more stable, but doesn´t corner as easy. That's why the neck post angle of the Springer fork on the Big Twins was changed in 1946: the tubes stand steeper than the steering angle. Viewed from the top, the upper ends of the fork leg ends stand in front of the steering head. The non-parallel design is called offset in Harley jargon. The design with parallel tubes and steering head is called inline.

Summarized, the following three categories can be found with Springer forks:

  • Inline. Original on Big Twins 1936-1945 and 45"/750cc Flatheads 1941-1957. Side tubes and steering head parallel. The rake (fork extension) here is 0°.
  • Offset -3°. Original on Big Twins 1946-1948. The side tubes are steeper than the steering head. The fork rake is therefore -3°.
  • Offset +3°. Not original. This comes from the custom department and applies to all our Springer forks in 8", 12" and 16" overlength. The stem of these forks is inclined to the front by 3°. This is done to avoid a steering neck so high and inclined that the bike is impossible to steer.

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com