Classic Springer Forks 2” and 4” Longer than Stock
- Springer fork »Classic Inline« by Samwel Supplies
- fits Big Twins
- internal thread of neck post: 3/4”-14 UNS
- steel, black, powder-coated, black springs
- length: 53.5 cm
- length over/under stock: +2 ”
- with material certification
- Europe
- gross weight: 20.73 kg
Extended Springer forks which provide more ground clearance when building bikes with larger than stock neck rakes. Actually, the +2” versions were factory equipment on XA and 1941 WLA military models. Made with forged legs, just like the shorter versions. They feature a fork stem with two Ø1” bearing seats for the use of 1949-up tapered roller bearings without any modifications.
Length is measured from axle center line to seat of lower steering head bearing.
Although these Custom forks are intended for 1936-1957 rigid frame Big Twins they can be mounted with later frames, too, provided you have/install matching frame head beariings. The builder has to consider rake, trail, overall chassis geometry, brake function, etc.
Internal Threads on the Upper End of the Legs
For custom riser installation the fork legs have M20x1.5 internal threads at the upper end and accept riser adapter studs or plugs which are available separately; an extra added by the manufacturer which saves you a lot of work and axle grease.
Inline vs. Offset
Classic Springer Forks are produced for different frame rakes.
- In the beginning, both the main tubes and the steering stem were in the same plane. This is called "inline". The rake is 0°. Of this type were all 45” Springer forks 1936-1957 and all Big Twin forks 1936-1945.
- From 1946 onwards the Big Twins had the neck angle increased to 30°. To maintain fork inclination and ground clearance, the steering stem was tilted to the rear by 3°. We call these forks Offset -3°, they were stock on 1946-1948 Big Twins.
- When building a bike with ≥+8” extra long forks you don’t want the steering neck so high and inclined that the bike is difficult to steer. Therefore such forks are manufactured with a positive rake, i.e. the steering stem is inclined to the front by 3°. We call these forks Offset +3°.
The sketch shows the placement of the lateral tubes and steering stem seen from the drivers place. Now it is clear, too, why there have to be three different types of top trees or handlebars for Classich Springer forks.
Parkerized Rockers
As a running change the manufacturer currently changes all black powder-coated rockers to a parkerized finish, as it was original back in the days. For a transition period W&W Cycles will have both types in stock, so if this is important for you, please contact our sales staff and let them know your preference.
1.) The pivot point of the brake shackle on the backing plate or caliper bracket must not be positioned vertically above or in front of the wheel axle (driving direction). In this case the moving forces in your fork parallelogram will be reversed and the fork will rebound instead of being compressed when you apply the brake. This will generate very high forces to impact on your rigid fork leg with possible damage.
2.) Caliper bracket or drum brake backing plate must float on the wheel axle. If not, the fork will rebound as well when applying the brake. Result: see above.
Spare parts:
Accessories:
18-655
Bates Fender Mounts
Bearing Adjuster Nuts for Classic Springer Forks
OEM Style Top Fork Clamps
Steering Head Bearing Races and Cups for Ball Bearings →1977
Acorn Steering Head Nuts
Fork Spring Covers
Springer Rockercovers
Bates Riser Adapters
Steering Damper Assemblies Springer Fork
Bike Station Shock Absorbers for Classic Springer Forks
Nacell Top Plugs for Classic Springer Forks
Have any questions?
Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com