Shop Chassis Frames
Lowbrow KR Style Hardtail Sections for Sportster 1967-1978

Lowbrow KR Style Hardtail Sections for Sportster 1967-1978

Price and stock:
Item №
15-948
Price incl. VAT
630.95 €
Available
2
Ready for immediate delivery from our Würzburg, Germany warehouse
The price includes 100.74 € German VAT.
piece
Save to wish list
  • Hardtail section »KR Style« by Lowbrow Customs
  • fits Sportster 1967-1978
  • steel, bare
  • with Mounting Kit, Rear Axle Adjusters
  • USA
  • gross weight: 7.05 kg

In addition to the straight leg style bolt-on hardtail sections, that are mostly used for chopper projects of Ironhead Harley-Davidson motorcycles, Lowbrow Customs now offers rigid bolt-on hardtails sections that are inspired by the early KR race bikes with the looped frame. So if you are looking for something special for your next Ironhead Bobber project and are nostalgic about racing, you can kill two birds with one stone by using this hardtail. The frame tubes on these tail sections are bent in one piece, just like back then, and the axle plates are welded into the loop. Mounting can be done without much difficulty and without messing up the original frame too much. Made by hand in the USA, Ohio, from 1" x 0.125" thick steel tube, and 5/16" thick axle plates.

Fits all 1967-1978 ironhead sportsters (1967-1969: only XL and XLH). Most stock installed components remain. Rear wheel, axle and brake can be remounted as before. Rear axle adjusters and a frame mounting kit are also supplied. For correct assembly, 2" of the rear fender struts must be cut off, otherwise the frame remains untouched. The bike's dimensions will change by 4" in length and -2" in height. This means that you will need a longer secondary chain and longer brake rods.

See also:

LeBeeF Brackets for Narrow Glide Forks

LeBeeF Brackets for Narrow Glide Forks

Custom bracket to fasten bottom mount head lamps on narrow glide forks with lower tree pinch bolts spaced at 122-125 mm center-to-center. Bolts are not included.
more …
Bates Ventura Handlebars

Bates Ventura Handlebars

Cruise the Sunset Blvd in style or plow your favourite gravel road - the Ventura bars will do a great job in both situations. Their design, which was often nicknamed Buckhorn, is exactly made after the 1959 XLCH factory equipment. They provide an upright seating position and good control on bumpy roads.
more …
Lowbrow Mid-Tunnel P-Nut Gas Tanks

Lowbrow Mid-Tunnel P-Nut Gas Tanks

Nothing changes the look of your hand-built custom motorcycle like a bobber gas tank such as this. The Lowbrow P-Nut gas tanks are based on the old Wassell peanut gas tanks available in the 1950's - 70's. The Lowbrow versions are made from heavy gauge (1mm, approximately 19 gauge) steel, which translates they are much thicker, and the fabrication is of higher quality, than the originals. The Mid Tunnel Peanut has a tunnel that runs about midway through the gas tank, bringing it higher off the backbone than the original (deep tunnel) version.
more …
Bates Tires Baja 100

Bates Tires Baja 100

Gravel, rocks and roadkill – here’s an awesome tire knowing no fear. Whistle into town, come back home across the fields Steve McQueen style. Do some hooligan racing among friends on the neighborhood dirt track. Or what about that camping trip to that place where the road ends you’ve been postponing all those years? The Bates Baja tires can handle it....
more …
Throttle Addiction Wassell Ribbed Fenders

Throttle Addiction Wassell Ribbed Fenders

Sturdy alternative to the original aluminium Wassell ribbed fenders. Made of 2mm thick steel, this fender withstands even heavy loads and a passenger can sit on them without any worries. Works great with 18" tires or with high-shouldered 16" vintage style tires.
more …
The GasBox 2-2 Header Pipes Sportster 1962-1964

The GasBox 2-2 Header Pipes Sportster 1962-1964

Reproductions of the stock headers for Sportster 1962-1964. However, they will fit all Ironhead Sportster models (except 1979) and can be combined with both original and Custom mufflers.
more …
Bates Tuck & Roll 1

Bates Tuck & Roll 1" Solo Seats

An almost iconic custom part of the past is the Bates solo seat. Sleek looking and easy to mount it was and is the seat of choice for many choppers and bobbers. These reproductions are meticulously made after the period accessories, with no detail left out. This means the detachable leather cover is fixed to the correctly fabricated and zinc-plated base plate with Phillips screws and countersunk washers.
more …

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com