Shop Handlebars Cables
Cable Clamps, Guides and Accessories

Cable Clamps, Guides and Accessories

Coil Housing Covers for IOE and V-Models
Coil Housing Covers for IOE and V-Models
A detail for the perfectionist. Leather control coil housing covers which fit all HD models from 1909 to 1936. Also fit racing models and other vintage American motorcycle brands.
more …
Control Coil Brackets and Clamps 1910-1936
Control Coil Brackets and Clamps 1910-1936
Perfect reproductions of the control coil brackets and clamps as used on early H-D models.
more …
Control Coil Adjuster Bolts 1915-1936
Control Coil Adjuster Bolts 1915-1936
Reproductions of the control coil adjusters on early H-D models.
more …
Clamps for Control Cables 1928-1957
Clamps for Control Cables 1928-1957
more …
Control Coil Brackets 1936-1948
Control Coil Brackets 1936-1948
more …
Control Coil Brackets and Clamps 1949-1964
Control Coil Brackets and Clamps 1949-1964
more …
Brake Cable Lubricators
Brake Cable Lubricators
Precise reproduction of the stock cable oiler with clip for pre-war models. Available for original and aftermarket brake cables. Fits later models, too.
more …
Control Coil Bracket 1952-1974
Control Coil Bracket 1952-1974
more …
Clutch Cable Bracket for K Models and Sportster 1952-early 1970
Clutch Cable Bracket for K Models and Sportster 1952-early 1970
Reproduction of the clutch cable bracket which was attached to the front left frame tube on K Models 1952-1956 and Sportster models from 1957 to the early 1970s.
more …
Fuel Line and Cable Support Wire
Fuel Line and Cable Support Wire
This support wire is a must for properly routing the fuel line between your cylinders. It is chrome plated and replaces the OEM  support used on most models from 1966–89. Installs on the lower bolt of the carburetor manifold flange. May also be used as cable guide.
more …
Throttle Cable and Wire Clamp
Throttle Cable and Wire Clamp
more …
OEM Style Clutch Cable Bracket for Big Twins 1965-early 1979
OEM Style Clutch Cable Bracket for Big Twins 1965-early 1979
more …
Kuryakyn Clutch Cable Ferrule
Kuryakyn Clutch Cable Ferrule
Tricky chrome-plated die-cast cover for the rust-susceptible ferrule on clutch cables used on models from 1982 to present. Installs in minutes.
more …
Cable Guide Chrome
Cable Guide Chrome
Cable and hose guide, routes anything cleanly and securely, no more exhaust pipe contact.
more …
Clutch Cable Guide FLH
Clutch Cable Guide FLH
Factory equipment on FLH to route the clutch cable but can be used to guide any control cables and brake lines or as bolt-on eyelets to tie down the luggage.
more …
Clutch Cable Guide 5-Speed
Clutch Cable Guide 5-Speed
Fits all 5-speed models from 1980 to present. Prevents cable against damage through heat from headpipe or cylinder.
more …
Throttle Cables Clip
Throttle Cables Clip
Helps parallel routing and fixing of all OEM-type throttle cables 1981-up.
more …
Cable and Line Clamps OEM Type
Cable and Line Clamps OEM Type
Bolt-on multi-purpose clamps. Fasten brake lines, control cables and wiring harnesses.
more …
Plain Cable Clamps
Plain Cable Clamps
Clamps allow clean routing of clutch cables, throttle cables and brake lines.
more …
Ball Milled Cable Clamps
Ball Milled Cable Clamps
Clamps allow clean routing of clutch cables, throttle cables and brake lines.
more …
Barnett Screw-On Cable Pins
Barnett Screw-On Cable Pins
Cable pin with screw. Fits all Harley brake and clutch levers →1981. First aid for torn cables. A must for every tool pouch!
more …
Reverb Color Coils OEM Style
Reverb Color Coils OEM Style
Outstanding reproductions of the spiral color coils that were offered as accessory items by Harley-Davidson from 1955 onwards. Primarily used to beautify brake and clutch cables, they were also used to conceal old or worn out control coils. They quickly coil over cables and will surprise you with the new retro-look they give to your Harley-Davidson. Fit also to ignition or throttle cables.
more …
Reverb Color Coils Custom
Reverb Color Coils Custom
From 1955 onwards, spiral color coils were offered as an accessory by Harley-Davidson. Primarily used to beautify brake and clutch cables, they were also used to conceal old or worn out control coils. They quickly coil over cables and will surprise you with the new retro-look they give to your Harley-Davidson. Fit also to ignition or throttle cables.
These single-colored custom spiral sleeves are sold individually! However, two pieces are always required to either reproduce the original color combinations such as blue-white, green-white or black-white or to let your imagination run wild with your own color combinations.
more …
Müller Clutch Cable Adjuster
Müller Clutch Cable Adjuster
This aluminum clutch cable adjuster replaces the original plastic part and provides more and presice options to properly adjust the clutch cable on your Milwaukee Eight 2018→.
more …

Fasten Bowden cables

Bowden cable holders, guides and clamps are not only for tidiness, they also have a physical-technical side. Already in the patent drawing of Mr. Bowden's invention you can see that the cable sheath is fixed to the base plate with a small clamp at the apex of the bow. There is a reason for this: the cable sheath provides support and guidance for the inner cable, but must itself be attached to the frame or the Springer fork, because it in turn needs support points. On many bikes, you see the long Bowden cable from the handbrake lever down to the jumper drum brake hanging freely in the air. If such a rider complains about a lack of braking action, all you have to do is tell him to use the small thread on the left fork tube and use a clamp to tighten the cable there. Suddenly, the hand force is no longer wasted uselessly in the "flabby" cable sheath, but is properly transferred to the cable. The trick also works with the Hydra Glide fork or the long clutch cable of the FLH.

Original cable clamps and cable holders

Of course, Bowden cables can be secured to the frame and fork with cable ties or Velcro strips, but reproductions of the original, usually parkerized, cable clamps and guides are actually indispensable for a good restoration. Colony and Competition Distributing offer a complete range of parts used by the Factory for throttle and ignition cables, clutch and brake cables.

Pulling and cable cam accessories

Available as accessories are numerous handy clamps for cables, Bowden cables and brake lines, sometimes split for easier mounting and milled from aluminum.

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com