Accessories

Bates Drain Valve for S&S Carbs
Bates Drain Valve for S&S Carbs
Draining the S&S float bowl for a jet change or to remove water from it after heavy rain can be messy with gas flowing all over your engine and hands. This drain valve replaces the stock bowl plug and makes this a quick and clean job. Simply twist off the valve cap, which also serves as a closure cap, and open the integrated tire valve with a pointed object. Then you can drain the fuel or the accumulated water into a suitable container in a controlled manner. If the float chamber should be emptied completely, you can also unscrew the tire valve completely with the valve cap to drain the complete fuel.
more …
S&S Jetting Kit
S&S Jetting Kit
This kit contains all jets to properly set up and jet all S&S carburetors. Parts are stored in labeled, durable vinyl divider boxes.
more …
DynaMite Knee-Saver
DynaMite Knee-Saver
Running an S&S Super E or G carb on Knuckleheads and Panheads results in the Teardrop air cleaner sticking out pretty far and interfering with your right knee. This low profile version features a shortened cover and a modified base plate which reduces the overall height of the air cleaner assembly by 25 mm. Thus you gain more legroom and the whole air cleaner tucks closer to the engine. Looks good on other models, too.
more …
Bates Idle Adjuster
Bates Idle Adjuster
Idle adjustment of S&S and Bendix carbs can be annoying when your bike is equipped with Fat Bob gas tanks, especially the 5 gal versions. The Bates adjuster solves this problem once and for all. It features a flexible shaft and a large adjuster knob with knurled edge which allows carb adjustment without a screwdriver and as fast as you can say "****! I forgot my ******* tool roll in the garage!"
more …
Mooneyes Idle Adjuster Screws
Mooneyes Idle Adjuster Screws
These Mooneyes idle adjuster screws facilitate the adjusting of the idle speed and, with the cult Mooneyes ball, also cut a fine figure. The ball can be unscrewed and replaced with other Mooneyes valve caps.
more …
S&S High-Flow Filter Kit Super E and G
S&S High-Flow Filter Kit Super E and G
With larger and larger street engines becoming more common, S&S has developed a high flow air filter kit for Super E and G carburetors. The new filter is 1” wider than the standard filter and features a low restriction filter element. Combined with the larger surface area it adds an airflow increase of up to 37%! The filter and filter adapters extend the Teardrop housing by 1”, so the filter peeks out from under the Teardrop and imparts a high performance street racer look. Kit installs in minutes and includes pre-oiled filter element and three plated steel extensions.
more …
Bates Rotor Float Bowl Screws for S&S carburetors
Bates Rotor Float Bowl Screws for S&S carburetors
Float bowl screws for aesthetes, who set value on design and functionality. Meticulously machined on CNC equipment and tumble polished they feature nicely shaped hex heads which "flow" into the shafts. Admittedly, this takes time to make and is a bit costly, but the result is a feast for the eyes.
more …
Enrichment Devices for S&S Carburetors
Enrichment Devices for S&S Carburetors
Adjustable enrichment devices for all S&S carburetors. Especially for Super E and G carbs if you want to use a custom air cleaner and cannot retain the S&S enrichment lever.
more …
S&S Adjustable Support Bracket
S&S Adjustable Support Bracket
Universal mount, adjustable support bracket for S&S carburetors. Required to provide support function of a/c backing plate on carbs run without air cleaner, e.g. with Air Horns.
more …
The GasBox Carburetor Support Brackets Evo Sportster
The GasBox Carburetor Support Brackets Evo Sportster
This support bracket alllows you to use Custom air cleaners instead of the S&S equipment with a Super E or G carburetor. Built with 1/8” thick steel.
more …
The GasBox Carburetor Support Brackets BT OHV 1936-1984
The GasBox Carburetor Support Brackets BT OHV 1936-1984
This carb support bracket is made to support your intake manifold in order to keep your carb up and safely route your gas line keeping it off the cylinders. Will work with most carburetors.
more …
The GasBox Carburetor Support Brackets Ironhead XL
The GasBox Carburetor Support Brackets Ironhead XL
This Ironhead Sportster carb support bracket is made to bolt to your intake manifold and front intake tappet guide bolt. Will work with any carburetor.
more …
Thunderjet Third Fuel Circuit
Thunderjet Third Fuel Circuit
Third fuel circuit for Bendix, Tillotson, Keihin (except CV) and S&S carburetors. It has a built-in air correction system that permanently solves the problem of poor mid-range and/or lean top end performance. This system operates over a wide range of altitude and atmospheric conditions and is available in blue, red or black anodized finish.
more …
Bates Adapter for Linkert Carb Covers on S&S L-Series
Bates Adapter for Linkert Carb Covers on S&S L-Series
The selection of carb covers for Linkert carburetors is pretty extensive and many of them look nicely at home on other carbs, too. With this little adapter plate you can make this happen in no time. Precisely CNC-machined from billet for a hassle-free installation.
Since the bolt circle for Linkert carbs is smaller the adapter somewhat restricts the air intake. All you performance nuts should consider this.
more …
Bates Adapter for Linkert Carb Covers on S&S Super B
Bates Adapter for Linkert Carb Covers on S&S Super B
The selection of carb covers for Linkert carburetors is pretty extensive and many of them look nicely at home on other carbs, too. With this little adapter plate you can make this happen in no time. Precisely CNC-machined from billet for a hassle-free installation.
Since the bolt circle for Linkert carbs is smaller the adapter somewhat restricts the air intake. All you performance nuts should consider this.
more …
Bates Adapter for Bendix Air Cleaners on S&S Super E/G Carbs
Bates Adapter for Bendix Air Cleaners on S&S Super E/G Carbs
This adapter allows for the installation of Bendix, Keihin (Butterfly) and Super B type air cleaners (with flat base plate), covers and air horns on S&S Super E/G carburators.
more …
Bates Adapter for Linkert Carb Covers on S&S Super E/G
Bates Adapter for Linkert Carb Covers on S&S Super E/G
The selection of carb covers for Linkert carburetors is pretty extensive and many of them look nicely at home on other carbs, too. With this little adapter plate you can make this happen in no time. Precisely CNC-machined from billet for a hassle-free installation.
Since the bolt circle for Linkert carbs is smaller the adapter somewhat restricts the air intake. All you performance nuts should consider this.
more …
Bates Adapter for Oval Air Cleaners on S&S Super E/G Carbs
Bates Adapter for Oval Air Cleaners on S&S Super E/G Carbs
Add some classic factory style to your S&S Super E or G carburetor. This adapter allows for a quick and clean installation of OEM or aftermarket air cleaners with recessed backing plate. At least that’s what it is intended for, but of course you can mount any air cleaner, carb cover or air horn with a Tillotson, Bendix or Keihin (exc. CV) bolt pattern to your Super E/G with it.
more …
Helix PU Carburetor Vent Lines/Overflow Hoses
Helix PU Carburetor Vent Lines/Overflow Hoses
These transparent lines by Helix can be used as carburetor vent lines or overflow hoses. They are made from premium polyurethane with a Shore hardness of 85, which provides for superior resistance against abrasions, kink, tear, oxidation and chemical influences. It has a melting temperature of 188°C and an operating temperature range of -59° to +68°C. This line material will not get hard and stays flexible.
more …
Fuel Line Insulator
Fuel Line Insulator
Flexible insulator tube which protects the fuel line from scuffing or against heat influence when running it between the cylinders.
more …
Pingel -6AN Fitting for S&S Carburetors
Pingel -6AN Fitting for S&S Carburetors
For all S&S Super E/G carburetors we also offer a -6AN fitting to replace the slip-on fitting on the float bowl.
more …
Kustom Tech Single Throttle Cable Actuation Disc
Kustom Tech Single Throttle Cable Actuation Disc
This single cable throttle spool and cable bracket will add some custom look to your S&S Super E/G carb.
more …
Throttle Cables for FL 1975, FX 1974-1975, XLCH 1974-early 1976 (Bendix Carb)
Throttle Cables for FL 1975, FX 1974-1975, XLCH 1974-early 1976 (Bendix Carb)
more …
Throttle Cables for Throttle Grip Sets →1980 with Bendix/S&S Super B
Throttle Cables for Throttle Grip Sets →1980 with Bendix/S&S Super B
more …
Throttle Cables for Throttle Grip Sets 1981-1995 with Bendix/S&S Super B
Throttle Cables for Throttle Grip Sets 1981-1995 with Bendix/S&S Super B
more …
Throttle Cables for Throttle Grip Sets 1981-1995 with S&S Super E+G
Throttle Cables for Throttle Grip Sets 1981-1995 with S&S Super E+G
more …
Throttle Cables for Throttle Grip Sets 1996→ with S&S Super E and G
Throttle Cables for Throttle Grip Sets 1996→ with S&S Super E and G
more …
S&S O-Ring Manifold Clamps
S&S O-Ring Manifold Clamps
High quality intake manifold clamps to replace the flimsy and troublesome stock clamps. They use a curved 10-24 threaded T-bolt with plated steel aircraft hex locknut.
more …
S&S Rubberband Manifold Clamps
S&S Rubberband Manifold Clamps
High quality intake manifold clamps to replace the flimsy and troublesome stock clamps. They use a curved 10-24 threaded T-bolt with plated steel aircraft hex locknut.
more …
Bates Carburetor Support Brackets BT OHV 1936-1984
Bates Carburetor Support Brackets BT OHV 1936-1984
more …

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com