Modern Custom

Designed to look good on all kinds of cafe racers, choppers and bobbers. The nostalgic appearance hides a full SMD-LED circuit board which works as running light, brake light and number plate illumination through a window on the underside. The sturdy housing mounts directly with two studs to all flat surfaces or with an optional bracket.

Designed to look good on all kinds of cafe racers, choppers and bobbers. The nostalgic appearance hides a full SMD-LED circuit board which works as running light, brake light and number plate illumination through a window on the underside. The sturdy housing mounts directly with two studs to all flat surfaces or with an optional bracket.

Designed to look good on all kinds of cafe racers, choppers and bobbers. The nostalgic appearance hides a full SMD-LED circuit board which works as running light, brake light and number plate illumination through a window on the underside. The sturdy housing mounts directly with two studs to all flat surfaces or with an optional bracket.

A distinctive designed which stands out and which will look cool on many kinds of Custom bikdes. Features a full SMD-LED circuit board which works as running light, brake light and number plate illumination through a window on the underside. The Big Fin lamp mounts directly with two studs to all flat surfaces or with an optional bracket.

This LED taillight features a distinctive design that looks great on many custom bikes. It combines taillight, brake light, and license plate illumination in a compact housing.
Thanks to the attached studs, the housing can be mounted on almost any flat surface, such as a sissy bar, rear fender, or other suitable locations on choppers, bobbers, and custom bikes.

A modern version of the old style chopper taillight called The Box. It is equipped with a dual function LED cluster that acts as both brake and running light. The housing is made of billet aluminum and will stand up to years of hard road use. Two back studs make installation a snap.

Features a body diameter of 56 mm and a lens diameter of 50 mm.

Stunning and innovative is this new generation of taillights featuring LED technology that look way cool.

Plastic housing for flush-mount installation.

For the installation on flat surfaces like fender or license plate carrier.

Maintain the fender’s flowing lines by simply bolting on this lens. Gives dressers a lean tail.

This great looking taillight is especially designed for Fat Bob fenders. It fills the entire area of the fender and gives your bike a unique look. Fits all FXWG and Softail models from 1980 to present or our Fat Bob fenders.

This taillight features a housing that is machined from billet aluminum. The nicely designed rim with ornamental drillings accepts accessory Fin Faces which are available separately. The mounting bracket is made from steel.

Extremely small and spectacularly bright combination of taillight and stop light. Its light surface would fit four times on a 1 Cent coin! This offers amazing styling options for your motorcycle. Until activated the Atto Dark turn signal stays almost invisible on your motorcycle due to its black housing and dark tinted lenses. But then it flashes with an intensity unprecedented with this size. Besides the proven Kellermann HighPower LED technology it uses EXtranz technology (=Extreme Optical Transparency). All electronics are housed in the tiny casing, so it can be directly plugged into the 12 volt system. Available for horizontal or vertical mounting.

Atto goes integral. The Atto Integral has all the features of the Atto and is even more invisible as a built-in component on the bike than the Atto with a mounting thread. With a diameter of just under 9 mm, it fits into all possible surfaces on the bike, such as saddlebags, fork covers or DIY housings.
The electronics for controlling the LEDs are completely contained in the aluminum housing. The Atto Integral can therefore be connected directly to the 12 V power supply. If used as turnsignals, you will need to check turn signal frequency, as with all LED-based turn signals on Harley-Davidson motorcycles.
Until lit, the Atto RB Integral Dark taillight stays almost invisible on your motorcycle.

Extremely small and spectacularly bright combination of taillight and stop light. Its light surface would fit four times on a 1 Cent coin! This offers amazing styling options for your motorcycle. The Bullet Atto RB literally disappears on the bike and will only draw attention when it really has to. But then it flashes with an intensity unprecedented with this size.
All electronics are housed in the tiny casing, so it can be directly plugged into the 12 volt system. Vertical mounting, especially as single, centrally mounted taillight.

Atto goes integral. The Atto Integral has all the features of the Atto and is even more invisible as a built-in component on the bike than the Atto with a mounting thread. With a diameter of just under 9 mm, it fits into all possible surfaces on the bike, such as saddlebags, fork covers or DIY housings.
The electronics for controlling the LEDs are completely contained in the aluminum housing. The Atto Integral can therefore be connected directly to the 12 V power supply. If used as turnsignals, you will need to check turn signal frequency, as with all LED-based turn signals on Harley-Davidson motorcycles.
Due to its size, the Atto RB tail light is very difficult to spot on the bike even in the clear lens version.