for Cams

Cam Shaft Bushing Reamers OHV Big Twins 1936-1969
Cam Shaft Bushing Reamers OHV Big Twins 1936-1969
Professional tool to correctly ream the gear cover cam shaft bushing after press-in. Comes with pilot bushing for the crankcase cam shaft bearing.
more …
Jims Cam Bearing Extractor
Jims Cam Bearing Extractor
For Big Twins 1958-up. Use to remove inner cam bearing without splitting cases.
more …
Cam Cover Puller
Cam Cover Puller
Removes cam covers without damaging sealing surface.
more …
Jims Support Plates for Gear Cover
Jims Support Plates for Gear Cover
If you ever tried to change a Big Twin cam cover bushing on an arbor press, then you know that it is very difficult to install the new bushings straight into the corresponding bores. The Jims holding tool definitively solves this problem. Just bolt the cam cover to the fixture for secure working - no scratched cam covers and no misaligned bushings anymore.
more …
Jims Inner Cam Bearing Installation Tool
Jims Inner Cam Bearing Installation Tool
After the old cam bearing has been removed with tool WW 98-192, this installation plate is used to smoothly press the new needle bearing into the right case with the motor assembled. Kit comes complete for all Big Twin from 1958 up but may be used as well for cam bushings on OHV models from 1936 up with the proper press plug.
more …
Andrews Gauge Pins
Andrews Gauge Pins
Precision machined gage pins used to determine the pinion gear diameter. Available in two sizes. Use the .105“/2.67 mm pins for models thru 1989 and the.108“/2.74 mm pins for models 1990 - up. Sold in pairs, because correct measurement requires two pins.
more …
Camshaft Needle Bearing Mandrels
Camshaft Needle Bearing Mandrels
To install needle bearing without damages. For all cases and cam covers of Big Twin or Sportster engines.
more …
Cam Shaft Bushing Reamers Flathead and Sportster
Cam Shaft Bushing Reamers Flathead and Sportster
Use to ream cam bushings on various models.
45”/750 cc W & G models 1937-1973, Big Twin Flathead 1937-1948: case bushings, cover bushings front intake and exhaust., K-models 1952-1956: case bushings, cover bushings front intake and exhaust, rear exhaust., Sportster 1957-1985: cover bushings front intake and exhaust, rear exhaust.,
more …
Jims Cam Shaft Needle Bearing Installation Tools for Twin Cam
Jims Cam Shaft Needle Bearing Installation Tools for Twin Cam
This tool will install the two inner cam needle bearings on Twin Cam engines. It perfectly aligns to the shaft bores for a precision press fit.
more …
Jims Inner Cam Bearing Extractor Twin Cam
Jims Inner Cam Bearing Extractor Twin Cam
Professional tool to remove the inner cam bearings.
more …
Jims Cam/Crank Sprocket Lock Tool Twin Cam 88
Jims Cam/Crank Sprocket Lock Tool Twin Cam 88
This tool is made from delrin material and allows to lock the cam and crankshaft sprocket to properly remove, replace and retorque the sprocket bolts.
more …
Jims Cam Chain Tensioner Blocking Pins for Twin Cam 88
Jims Cam Chain Tensioner Blocking Pins for Twin Cam 88
This tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble the cams in Twin Cam engines. It also checks spring loads on the chain tensioners.
more …
Cam Cover Bushing Reamers Sportster
Cam Cover Bushing Reamers Sportster
Use to ream the rear intake cam cover bushing on Sportster models 1967-1985.
more …

Special Tools for Camshafts

You don't actually need any tools for the camshafts themselves. But for all the associated work, such as installation and removal, preparing bearing bushes and inserting or pressing out needle bearings or ball bearings. You need pullers, extractors, pressing mandrels, reamers and blocking tools tailored to the specific Harley model.

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com