Fender Mounting

Front Fender Mounting Kit for IOE Models and Singles

This kit includes two nuts and bolts to mount the front fender on the fork.

more …

Fender Mounting Kit for IOE models and Singles

This master kit includes all nuts and bolts to mount the front and rear fender. Correct for models 1909-14 but many components work for later models, too.

more …

Filler Plate Kit

The filler plate kit fastens the rear fender of all 1911-1929 models to the upper frame bridge.

more …

The Cyclery Fender Brace Butterflies

A small part which makes a big difference - at least for the connoisseur. This neat little butterfly was used to hold the 5/8” wide fender braces in place on all models 1934-1939. The factory spot welded it but you can TIG-weld or braze it, too. Three are needed per bike, two on the front and one on the rear fender.

more …

Mounting Kits for Springer Front Fenders

Detailed kits consisting of reproduction screws, nuts and lockwashers to mount original or reproduction fenders on models with Springer style fork and rigid frame.

more …

Mounting Kits for Rear Fenders

Detailed kits consisting of reproduction bolts, nuts and lockwashers to mount original or reproduction fenders on the struts and frame.

more …

Brace Bolts for Rear Fender End

Accurate reproductions of the stock carriage bolts and nuts to fasten the rear fender hinged end to the fender braces.

more …

Strange Bird Fender Clamps OEM Style

Restoration quality fender clamps which feature an asymetrical design just like the original counterparts so they will snugly fit the fender’s outline and the rigid frame’s cross tube.

more …

Fender Clamps Custom

Universal use fender clamps which fit all rigid frames.

more …

Bates Fender Mounts

Very nice solution for mounting a small custom fender on your Classic Springer fork close to the front tire of 19” or 21” wheels. These clamps with brackets feature a smart design with only two tiny set screws visible. They install in minutes on the spring fork and hold your choice of a custom mudguard. Bolt hole distance on the brackets is 65 mm, with a maximum fender width of 120 mm. With stock FXSTS fenders you get a straightforward bolt-on solution. The selection includes clamps for OEM Springer forks and clamps for W&W Classic Springer and I-Beam forks.

more …

OEM Style Fender Struts

Fender struts for the rear fenders of various models. All struts are formed from high-grade steel and pre-drilled with the correct mounting holes before polishing and plating.

more …

LeBeeF Flat Fender Struts Bolt-on

Custom style from the 60’s and 70’s. These sturdy fender struts are cut from 8 mm steel and will make installation of your flat rear fender a lot easier.
Fully assembled fender struts which will bolt right on your stock frame.

more …

Custom Fender Mounting Kits

Nice detail for fastening the rear fender to the fender struts. Countersunk bolts with special low profile washers to create a unique and clean custom look. Small things like these often make the big difference.

more …

Rick’s Fender Mounting Kit Softail

For the installation of custom strut/rear fender combos. Four socket head bolts with special hemispherical washers which completely enclose the bolt heads.

more …

Lowbrow DIY Fender Struts Kit

This do-it-yourself kit includes everything you need to make some nice, clean fender struts that are beefy enough to support your fender and then some. It is all steel so you can TIG weld it up, paint, powder-coat or chrome however you want it it and hit the road. Included are:
2 x full radius bungs, 3/8"-16, 2 x counterbore bungs, ID 3/8", 2 x threaded bungs, 3/8"-16, 1/2" long, 2 x button head socket bolts, 2 x socket head bolts, 2 x rods 1/2" thick, 18" long,

more …

Lowbrow Upper Weld-on Fender Brackets

Upper fender mount brackets which are meant for welding to the frame cross bar. Made from 1/4” steel material, which you can cut, grind, file or weld to make them fit. Slightly radiused with two 1/2” spacers so they also fits against ribbed fenders, but can be bent or flattened out to fit the profile of your individual fender.

more …

Lowbrow Lower Weld-on Fender Brackets

Lower fender mount brackets which are meant for welding to the frame cross bar. Made from 1/4” steel material, which you can cut, grind, file or weld to make them fit.

more …

The GasBox Weld-on Fender Bracket

Cast steel, weld-on fender mount brackets which are meant for welding to the frame cross bar on rigid frames. You can cut, grind, file or weld on these to make them fit. The radiused side that fits against your fender can be radiused more or flattened out to fit the profile of the fender you are using.

more …

Throttle Addiction Sissy Bar Frame Mounts

Nicely machined lower mounts to build your own design of a sissy bar. Drilled to accept 9/16” tube or rod material which can be welded or brazed in.

more …