We use cookies for analytics, advertising and to improve our site. To find out more see our privacy policy.

Control module »mo.unit V.2« by motogadget

Item №
13-903

The mo.unit basic is the digital control unit for your motorbike – the heart of the entire on-board electrical system. It can be operated using buttons or using conventional handlebar switches. It controls all necessary components on the vehicle while also performing fuse functions.

There are considerably fewer relays and individual components in the wiring harness and the vehicle can be rewired with less effort in a very short amount of time. When using the mo.button, all switch connections are reduced to one single cable.

Features

  • Digital control using buttons possible with 4 or 5-button operation. Also latching switches possible
  • Replacement for the fuse box. 10 independent circuits are digitally monitored and switched off if there are faults. After the fault is rectified, the safety function is automatically reset
  • Integrated alarm system that can be installed in any position
  • Integrated, digital flasher relay that is load-independent; automatic switch-off optional and can be set; mo.wave mode can be selected
  • Integrated hazard warning light.
  • Turn signal can optionally be set as a positioning light
  • Integrated parking light and headlight flashing
  • Lo-beam and hi-beam (up to 120 W switched capacity) can be controlled using only one button.
  • Integrated, digital brake light modulator; flashing mode can be programmed
  • Acceleration-controlled emergency brake light (automatic warning signal)
  • Integrated starter relay for the starter system with solenoid (up to 30 A switched capacity)
  • Intelligent and configurable management/switch-off of power consuming devices so that the maximum starting energy from the battery can be used when starting the motorbike
  • Integrated, digital horn relay.
  • Two configurable additional outputs AUX1 and AUX2
  • Diagnostics function for assigning inputs, outputs, the circuit switching status, short circuit diagnostics etc.
  • Calibration and current measurement enables faults to be detected on all lamps
  • Absolutely waterproof and vibration resistant

  • mounting hole distance: 74 mm
  • L x W x H: 90 x 53 x 30 mm
  • net weight: 180 g
  • 6/12 V
  • with 50 cm battery cable, 2 wire eyelets, 3 x M5 stainless steel screws, 1 x speed sensor, installation and operating instructions
  • Germany
  • gross weight: 369 g
net price*
$265.94
* United States of America: Tax free shipping. Please check your local import fees.
In stock. Ready for immediate delivery from our Würzburg, Germany warehouse.
kit
Save to wish list

Accessories:

motogadget mo.button

motogadget mo.button

Further reduce and simplify your m.unit based wiring harness by using this little m.button device. Installed into the handlebar tube - or any other adequate location - this tiny cylinder will electrically connect all handlebar instruments, switches and buttons. With state-of-the-art bus technology, the m.Button digitally processes signals and transmits them to the m.unit V.2 over a single thin wire. The electrical consumers will then be switched inside the m.unit. All control wires are moved into the handlebar. This saves space, weight and time. A must-have for custom bikes with clean-look handlebars.<br />Simple facts:<br />Normally, the operating current (e.g. to headlight or turn signals) is transmitted directly via the wiring of the handlebar switches. Due to the high currents, cables with large cross-sections have to be routed from the fuse box to the switch and back to the electrical consumer. <br />The result: fat wire bundles. Definitely, a 'no go' for custom bikes with restricted space or a concealed electrical system.<br />Using the m.unit in combination with the m.Button, all switches/buttons on the handlebar are connected at the shortest distance possible to the m.button and from there only ONE thin wire runs to the m.unit. All loads and currents will be switched directly at the m.unit. A layout reduced to the max!<br />The m.button is completely moulded, making it water-tight and resistant to vibrations. It features connections for<br /><ul><li>turn signal, left side</li><li>turn signal, right side</li><li>headlight (low beam and high beam)</li><li>E-starter</li><li>horn</li><li>brake light switch, front brake</li><li>can be used with 6V and 12V electrical systems</li></ul>
more …

Have any questions?

Our service team will be glad to help out: Mondays - Thursdays 09:00-16:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail: service@wwag.com