We use cookies for analytics, advertising and to improve our site. To find out more see our privacy policy.



>

>

S&S



A B C D E F G H I J K L M N O P R S T U V W Y Z

S&S

In 1958 George Smith and his wife Marjorie started a small company called S&S Cycle. Located in Blue Island Illinois, the Smith´s new company began by selling lightweight aluminum pushrods for Harley-Davidson Motorcycles. George Smith´s vision was clear and simple: "I want to make all bikes go faster". This was a goal he pursued for the rest of his life.Even through George an Marge Smith have passed away, the company they founded still shares that vision and S&S Cycle has grown to be the worlds most respected manufacturer of high performance engines and components for American V-Twins.

Visit Website 

Products by S&S in our web shop:

S&S HI-4N Ignition

A single/dual fire ignition system with many state-of-the-art features built in a very compact unit. It has four rotary switches for mode selection, advance rate, and rev limit (1500-9900 rpm). Modes are: single fire, dual fire , OEM curve, race curve, kick start, electric start , The aluminum housing protects against vibration, moisture, dirt and improves heat dissipation. Its flange features degree and advance direction markings on the flange. Installation becomes easier with the convenient cable notch in the housing which also helps to prevent cable damage. Built onto the back plate, the sensor/magnet housings protect the sensors from damage during installation. The sensor housings contain advanced flux concentrators (intensify magnetic fields) with high temperature resistant samarium/cobalt magnets for accurate and reliable triggering. For street use the manufacturer recommends coils with a minimum of 2 Ω. Coils with 4Ω or higher may be used but may not produce optimum output.

Throttle Housings for S&S Grip Assemblies

Left Grips for S&S Grip Assemblies

Fuel Line Insulator

Flexible insulator tube which protects the fuel line from scuffing or against heat influence when running it between the cylinders.

S&S Twin Cam Style Oil Filter Bracket

These filter brackets are machined from solid billet aluminum and polished, but since looking good isn´t everything they have some very useful features, too. First, the position of the filter has been shifted slightly to give additional clearance between the filter body and the crankcase for easier filter installation and removal. Second, they are machined to make it easy to install an oil cooler in the pressure side of the system. An oil coolers is especially useful for big inch applications, when towing a trailer or for riding in hot weather conditions. If the cooler is not needed, simply install pipe plugs (included) instead of the hose fittings.

S&S Tapered Quick Set up Kits with Air Cleaner and Exhaust

Okay, so maybe your budget isn´t ready for a new big ínch S&S engine yet. But better performance is still within your reach and you can have 10 extra rear wheel horsepower at a price that is about the best deal going. These kits consist of a set of S&S performance mufflers, a high flowing S&S teardrop air cleaner, and a jet kit to re-jet stock carburetors with all components installed in less than an hour. There is no engine work to do, and everything you need is included in the kits. They will fit on either a stock carburetor or a stock 2001-up Delphi style fuel injected throttle body. With the jet kit you can dial in the stock carb for maximum power gains and improved rideability when installed on carbureted bikes. Our testing has shown that fuel map adjustments are normally needed when installed on fuel injected models. It is recommended that the bike be calibrated by your local dealer to insure that the engine is receiving sufficient fuel.

S&S KN-Series Engines

Knucklehead - the name describes a true legend and this engine design is without a doubt one of the important milestones in the history of Harley-Davidson. Introduced in the year 1936 the ohv-engined models in short time became synonyms for sporting, fast and reliable touring machines. Economically this layout proved to be a huge success for the Motor Company, too, because brand followers - and many others - quickly realized the outstanding qualities of this motorcycle. Design and technology of the Knucklehead turned out to be supremely sound and it became the prototype of all Milwaukee Big Twins, which significantly influenced all successive model groups down to the present day. The KN-Series engines by S&S closely resemble the appearance of a stock Knucklehead engine. However, numerous reforms enhance power, engine life, and reliability. The main improvement in design is the 1958-65 style flywheel assembly, which uses a splined sprocket shaft and a Timken sprocket shaft bearing on the drive side. This increased flywheel stability and strenght became necessary to handle the significantly increased power development. The rocker arm cover “tins” are another modern improvement. They are made from die-cast aluminum, and instead of being held in place by the valve guide, they are held down by valve spring pressure. A special gasket on the bottom of the lower “tin” provides a positive seal, and is much easier to service if needed, since the valve guides do not have to be pressed. The selection includes 93” (1560 cc) engines with crankcases for early style chassis thru 1947, with 1955-64 tin primary and 1936-64 transmissions. S&S KN-Series engines come completely assembled and ready to run with a electronic S&S Super Stock ignition system and Super E carburetor.

S&S SH74-Series Early Shovelhead Style Engines

The legendary Early Shovelhead generator engine was made by the Motor Company for 4 years only, from 1966-1969, and today it’s a rare bird. This version by S&S with stock 74 cubic inches combines authentic retro style with today’s technology for thousands of trouble-free miles. Fully assembled with the best components S&S has to offer, so factory specs are at least met and in most parts exceeded. The latter include bullet-proof steel flywheels, reinforced connecting rods, billet oil pump, billet rocker boxes, and roller rockerarms. The installed S&S 513G cam provides higher lift and increased valve timing for better performance. Top end oiling is provided through the pushrods which makes external oil lines obsolete. SH74 Early Shovelhead engines are equipped with an S&S billet timer housing (empty: no ignition components). Ignition rotation is clockwise, like stock. Without intake manifold and carburetor, so you can choose whatever seems appropriate for your needs. Crankcases, cylinder heads and the gear cover have a cast finish, cylinders are black powder-coated and the rocker boxes are polished.

Oil Filter Cartridges for S&S SH and V-Series Engines

Oil filter cartridges which S&S Cycle recommends for their SH-Series (Shovelhead type) and V-Series (Evolution type) engines.

S&S SH80-Series Shovelhead Style Engines

Sometimes stock is enough and this is exactly what the SH80 Shovelhead engine provides. 80 cubic inches of Shovelhead performance which will reliably propel both your daily driver or your end-of-the-world expedition bike. Fully assembled with the best components S&S has to offer, so factory specs are at least met and in most parts exceeded. The latter include bullet-proof steel flywheels, reinforced connecting rods, billet oil pump, billet rocker boxes, roller rockerarms and a billet gear cover. The installed S&S H-grind cam is a dead-on reproduction of the stock H-D cam. SH80 engines come without intake manifold, carburetor and ignition so you can choose whatever seems appropriate for your needs. Crankcases and cylinder heads have a cast finish, cylinders are black powder-coated and the gear cover and rocker boxes are polished. Top end oiling is provided through the pushrods which makes external oil lines obsolete.

S&S SH93-Series Shovelhead Style Engines

The legend lives! For die-hard Shovelhead enthusiasts we offer these complete, ready-to-install Long Block engines, assembled by S&S builders with the finest parts on the market today. Start with the bullet proof crankcases, flywheels, cylinders, and heads which proved their performance since so many years, and finish with the latest premium valve train components. Crankcases and cylinder heads come with natural aluminum finish, the cast iron cylinders are black powdercoated. Billet gear cover, tappet guides, and rocker boxes look outstanding and offer the kind of performance you expect from an industry leader like S&S. What you can’t see inside the engine is just as impressive. The S&S Shovelhead style tappet guides are designed around the quiet, dependable Evolution style tappets. The corrected tappet guide bore geometry assures correct valve timing with carefully selected S&S Evolution style camshafts installed in the gearcase. The unique adjustable Quickee pushrods are collapsible for easy removal and installation, but are stronger than stock style pushrods. Inside the billet rocker covers are S&S’s exclusive forged roller rocker arms. Top end oiling is provided through the pushrods which makes external oil lines obsolete. To let them breathe deeply all S&S Shovelhead engines are supplied with a Super E carburetor because tests showed that it provides the best performance on the street. Last but not least S&S SH engines are equipped with S&S Super Stock ignition systems. All these features result in Shovelhead engines with the kind of quiet power that some folks may just have a hard time believing.

S&S V80-Series Evo Style Engines

For those who don’t want to go “big inch”, the S&S V80 engine provides a down-to-earth performance solution. With the same displacement and physical dimensions as a stock Harley-Davidson Evolution engine, the V80 fits in a stock frame just like the original power plant, but packs a bit more punch, thanks to the S&S 508 camshaft, 585 valve springs and high flow S&S cylinder heads. The V80 is built from the same superior materials as the larger S&S performance engines, so engine life is excellent. Available with natural aluminum or black powder coat finishes. Rocker housings and nose cone cover are chromed. Fuel and ignition systems are not included, so you can use the carburetor, air cleaner, and aftermarket ignition you may already have. The cylinder heads allow installation of stock length manifolds. V80 Evo Style engines are EFI compatible with aftermarket intake componenets and module - calibration required.

S&S Stock Bore Stroker Pistons

S&S Adjustable Support Bracket

Universal mount, adjustable support bracket for S&S carburetors. Required to provide support function of a/c backing plate on carbs run without air cleaner, e.g. with Air Horns.

S&S Super Stock Generator Cases →1969

Here is the remedy for Knucklehead, Panhead and Early Shovelhead owners with worn-out or damaged OEM cases. The all new generator style crankcases from S&S! While having an almost stock-like appearance at first glance, the closer inspection yields state-of-the-art design elements that improve overall engine performance and reliability. Typical features include: stock-like oiling methods with improved motor scavenging, work with OEM  cast iron oil pumps or S&S oil pumps, fit stock frame, factory installed left and right main bearing races and cam needle bearing, shafts for timer gear and generator drive gear, cylinder base studs, drain plug for thorough engine main-tenance, 1/4”-20 threads used for more readily available hardware, clearanced for long strokes up to 5”, machined for late style generators 58-up,

S&S Super Stock Alternator Crankcases 1970→

The guys from S&S did it again. It can be seen bright and clear that the folks from Viola, Wisconsin, know their stuff and actually build engines and not just engine cases. S&S Super Stock crankcases allow complete installation of any flywheel assembly in less than one hour and are designed to meet the needs of modern engine builders. S&S cases come with: Timken sprocket shaft bearing and races, cam needle bearing pre-installed , pinion shaft main bearing race pressed in and line-honed, pinion shaft bearing , Even the cylinder studs are already in place which results in substantial savings in labour. Additional parts supplied include case bolts and crankcase fittings, timing and magnetic drain plugs and instructions. As stock replacements or all-out racing applications these cases are made for the performance enthusiast. They are cast from 356-T6 heat treated aluminum alloy and additional material has been added to key areas for strength but these improvements do not affect fitting in stock frames. No grinding and special clearancing is necessary. State-of-the-art features like maximized crankcase oil scavenging efficiency and improved oiling methods add up to an overall construction that is hard to beat. Available for 1970-1999 Big Twins. All cases feature the 1992 and newer oil filter mounting bosses. OEM  oil pumps of the respective year group or S&S oil pumps 1981-up are simply bolt on.

S&S O-Ring Manifold Clamps

High quality intake manifold clamps to replace the flimsy and troublesome stock clamps. They use a curved 10-24 threaded T-bolt with plated steel aircraft hex locknut.

S&S 883 → 1200 cc Conversion Kit

Boost any 883cc Harley-Davidson Sportster to 1200cc without hassle. No machine shop, no rebalancing your stock 883cc flywheels, no cylinder head modifications… The dished piston dome keeps compression down to a streetable 9.4:1 with stock 883cc heads. This kit includes pre-honed cylinders, pistons, rings, wristpins, keepers , and is ready to assemble out of the box. Installing this kit takes then same time as replacing a stock top end. It’s just more fun when you’re done.

S&S Cylinders for Knucklehead

The cylinders by S&S are a must for high performance applications like stroker and/or high compression engines. They are reinforced with more material all the way through the casting. Length is 5.530“ so they work as replacements on stock 74“ engines. Not finish honed.

S&S Rubberband Manifold Clamps

High quality intake manifold clamps to replace the flimsy and troublesome stock clamps. They use a curved 10-24 threaded T-bolt with plated steel aircraft hex locknut.

S&S Forged Pistons 3-5/8” Big Bore Evo Stock Heads 4-1/4” and 4-1/2” Stroke

Forged big bore pistons by S&S for 4-1/4" and 4-1/2” stroke flywheels (88 cui./93 cui.) with stock 8-1/2" diameter. Sold as complete kits with front and rear piston, rings, bolts and clips.

S&S Forged Pistons 3-5/8” Big Bore Evo Stock Heads 4-5/8” Stroke

Forged big bore pistons by S&S for 4-5/8” stroke flywheels (96 cui.) with stock 8-1/2" diameter. Sold as complete kits with front and rear piston, rings, bolts and clips.

S&S Forged Pistons 3-5/8” Big Bore 1936-1984 OHV

Forged 3-5/8" bore stroker pistons. Applications for this piston include 88" (4-1/4" stroke). 93" (4-1/2" stroke), and 96" (4-5/8" stroke) engines with stock 8-1/2" diameter flywheels, and 98" (4-3/4" stroke) and 103" (5" stroke) engines with 8-1/4" small diameter flywheels. Sold as complete kits with front and rear piston, rings, bolts and clips. Made by Wiseco.

S&S Cylinders for Shovelhead with Pistons

The complete kits include front and rear cylinder, base and head gaskets and big bore style cylinder base nuts and 12-point head bolts.

Replacement Pistons for S&S 4” Big Bore Kit

S&S Teardrop Air Cleaners for OEM Carburetors

The world-famous S&S “Teardrop” air cleaner for all models. Offers significant increases in performance over stock air cleaner assemblies by means of a vortex cone and radiused air entryway. A 1996 Dyna-Glide and a 1997 Sportster 883 both gained five horsepower with the S&S Teardrop, without any other changes!

S&S Gasket Kits for Engines: P and SH Series

Replacement Valves for S&S Super Stock Evolution Cylinder Heads

S&S Gasket Kits for Engines: S&S V Series

S&S Mini Teardrop Air Cleaners

S&S Cycle shrank the iconic Teardrop’s shape to 85% of its original size and laid it over a Stealth air cleaner system. This yields a somewhat less dominant appearance of the carb than the regular Teardrop air cleaner. Machined openings around the rim add style and provide additional air flow. Each kit comes complete with filter element, breather system and mounting hardware.

S&S Cylinders for Evolution Big Twin

Stock 3-1/2” bore cylinders by S&S made as strong as the famous Sidewinder big bore cylinders. Can be used as stock replacement for Evolution models and feature additional fin surface for improved heat dissipation and rigid casting for more reliable gasket seal. Oil return passages are stock for simple installation. We strongly recommend these jugs for stroker engines.

S&S Gasket Kits for Engines: T Series

S&S Gasket Kits for Engines: KN Series

S&S Nostalgic Air Cleaner Cover

Special limited edition old style air cleaner covers for Super E/G carburetors. These polished covers are faithful reproductions of the original sand cast products with raised “S&S Cycle” writing instead of the modern “S&S Super”. These covers will be sure to bring back memories of the days when S&S L-series and Super B carbs were the hottest thing on the road. Perfect for an old school chopper!

Parts for S&S Super E and Super G Manifolds

S&S Power Tune Duals Header Pipes

Up your Touring model exhaust performance even more (up to 8 hp increase!) with this S&S header system featuring an independent dual look with hidden crossover. Full heat shielding with 220° coverage prevents any discoloring. The system lowers the rear header to reduce radiated heat to the passenger. Oxygen sensor bungs are installed. Compatible with all slip-on mufflers.

Replacement Heat Shields for S&S Power Tune Duals Header Pipes for Touring 1995→

These heatshield kits can be used as replacements or to convert your black pipe system to a chrome finish or vice versa.

S&S Rubberbands for Manifolds

S&S Nut Kits for Cylinder Base: Big Twin 1936-1984

S&S Super B/E Manifolds for Stock Engines

Manifolds for Shovel Sidewinder Engines

Special manifolds for longer than stock cylinders. To be used with S&S Super-E and G carburetors.

S&S VFI Dual Bore Tuned Induction System

The Tuned Induction systems are for riders who are seeking the greatest possible performance gains from their engines. By utilizing air column inertia and carefully timed gas dynamic pressure waves, the Tuned Induction systems ram additional air into the cylinders for increased power. The most pronounced effect of this natural “supercharging“ effect is increased midrange torque, right where the street rider needs it most. Air filter area is almost two times that of an S&S Teardrop air cleaner. The Dual Bore tuned induction system has independent tuned length intake runners, one for each cylinder. It fits dual bore S&S Magneti Marelli style EFI systems.

S&S Protective Air Filter Covers

Made from black, water-repellant nylon. They protect from rain and moisture without reducing the flow.

S&S Stealth Air Cleaner

The S&S Stealth air cleaner kits offer the enhanced performance of the S&S Stinger intake system but cleanly hidden under the stock HD Big Twin air filter cover 1999→. Will work with all air cleaner covers with central screw.

S&S Gaskets for S&S Manifold Flanges to S&S Cylinder Heads

Replacement Parts for S&S Air Cleaners

S&S Cam 561 for Evolution Big Twin

The cam that S&S uses in their Hot Set Up kits. Best suited for stroker motors up to 88 cui.with 9.5:1 and higher compression ratio or big inch engines up to 98 cui and compression ratios up to 9.5 - 10:1. Moderate duration makes for great mid range performance where most riding is done. Hi-lift springs and collars and adjustable pushrods are required. All clearances must be checked.

S&S Breather Valves

Stock replacement breather valves by S&S for all OHV Big Twins 1936–up.

S&S Crankcase Breather Reed Valve Evolution

The Evolution style S&S breather reed valve replaces the standard rotary breather valve in 1993→ Evolution Big Twin style engines. Installation is fast and simple. No aligning timing marks, and no rotating parts. There is a +.030“ oversized reed valve for engines with heavily damaged breather bores. How does it work? Unlike the rotary breather valve that has been used in Harley-Davidson big twin engines since the 1920‘s, the S&S crankcase breather reed valve is not dependent on the rotation of the crankshaft to make it open and close. Therefore the opening and closing times are not determined by crankshaft position. The functional part of the reed valve consists of three steel reeds that are normally in the closed position. When the pistons travel downward in the cylinders, the air in the crankcase is compressed and pressure in the crankcase below the pistons increases. This pressure causes the reeds to open, allowing the air, oil and oil mist in the crankcase to escape into the cam chest. When the pistons change direction and begin traveling back upward in the cylinders, a vacuum is created in the crankcase. The vacuum causes the reeds to close, preventing air from entering the crankcase. The effect is that a slight vacuum is maintained in the crankcase and oil scavenging is greatly improved. This is most significant at high rpm when the time available to get the air out is the shortest.

S&S Cams for Twin Cam with Chain Drive

The S&S 510C camshaft set is designed to be used with the stock H-D chain drive system and is an economical way to improve the performance of stock and slightly modified street engines. The S&S 510C cams are as quiet as stock but produce significant power increases across the rpm range, especially above 3000 rpm. The 510C cams are compatible with the stock splined chain sprocket used in 2000-up Twin Cam engines, but may be used in 1999 engines if the H-D 2000-up style splined rear cam sprocket is used. S&S’s 1999 FXD test bike produced 62 horsepower in stock con-figuration. Horsepower jumped to over 82 with 88 ft-lb. of torque after the installation of S&S .510" camshafts, adjustable pushrods, an S&S Super E carburetor and air cleaner, 6200 RPM Screamin’ Eagle ignition module, and S&S slip-on mufflers.

S&S 510 G Cams for Twin Cam with Gear Drive

Timing chain or gears? That is here the question. In High Performance engines S&S Cycle prefers gears so their camshaft design for the Twin Cam models features new gears which replace the stock chain drive, sprocket and tensioner system for the cams. While being only slightly noisier than a chain gears incorporate some very important advantages: increased timing accuracy by eliminating chain lash, almost zero wear compared to a chain, no wear particles in engine oil from tensioner & guides, absolutely safe operation, gears cannot fail and tear, The latter is a very important factor with the installation of high lift cams and strong valve springs. S&S Gear Drive camshafts are sold by W&W as complete kits which consist of two camshafts with pressed-on inner drive gears, two outer cam gears, cam bearing plate, four bearings, small parts and gasket.

S&S Cams for Twin Cam Engines with S&S Oil Pump

S&S/Gates High Strength Final Drive Belts

Powerful engines can cause a higher wastage of the final drive belts. S&S has teamed up with the Gates Corporation, a leading manufacturer of power transmission belts, to offer a series of secondary drive belts for many popular V-twin models. These belts feature Gates’ super strong X3N carbon cord material, which is significantly stronger than the Aramid cables used in many OEM final drive belts.

Gaskets for S&S Carburetors to Air Cleaner

O-Rings for S&S Super E/G Crankcase Breather Bolts

S&S New Style Stock Replacement 1200 cc High Compression Pistons

S&S forged stock replacement pistons for Harley-Davidson Big Twin models 1936-84. The modern alloys used in these pistons, coupled with the advanced skirt profiles, result in low engine noise and long engine life that could only be achieved with cast pistons in the past. They are available with 9:1 high compression. Sold as complete kits with front and rear piston, rings, bolts and clips.

S&S Installation Kits for S&S 510C Cams

Provides small parts needed to install S&S 510C chain drive cam sets.

S&S Cover for Air Horns

Reproduction of the most sought after part in S&S history: the L-series carb velocity stack cover. In consequence of a high request S&S decided to make a limited run of these covers. Like the original pattern the new one is sand cast. Sold without mounting brackets, which have to be fabricated. They fit all S&S or similar air horns.

S&S Pistons Evo Sportster Conversion 883cc-1200cc

An easy and economic way to increase displacement of 883 and 1100 Evo Sportster models to 1200cc. This kit with 3-1/2” bore forged pistons only requires to bore the stock cylinders from 3 inch to 3-1/2 bore, or purchase new 3-1/2 inch bore cylinders. No combustion chamber modifications or flywheel rebalancing is necessary. Compression ratio will be a very streetable 9.5:1. The piston skirts are coated for reduced friction during break-in.

S&S Tappet Guides for Evolution Big Twin

These tappet guides are designed to be stronger, wear better, and last longer than the original counterparts. Use them as stock replacement for OEM  lifter blocks #18623-85A and 18622-85A or to complete your Evo Super Stock crankcases and cylinder heads. Burnished aluminum finish.

S&S Tappet Guides for Twin Cam

The S&S version: Lifterblocks CNC machined from aluminum and polished. Fit stock or S&S engine cases. With chromed socket head hardware.

S&S Tappets for Knucklehead

These tappets include adjusting screw and locking nut.

S&S Tappet for Evolution Big Twin and Sportster

These hydraulic tappets feature numerous significant design improvements and are perfect for stock replacement as well as high performance applications. A 3.12mm larger inner bearing race reduces stresses to increase axle, bearing, and roller life. A redesigned plunger assembly better withstands forces associated with heavy-duty valve springs and cams typically used in high-performance applications. Another feature is a revised metering device which precisely controls oil delivery to top end, insuring rapid lifter pump-up and reducing possibility of oil starvation to bottom end. Each lifter body and plunger assembly is hand-fit and then pressure-tested to insure correct operation.

S&S Semi Solid Adaptor for Evolution Big Twin

These adaptor rings limit the travel of the stock hydraulic units. = They work like solid lifters at high rpm while retaining regular hydraulic function under normal conditions. Recommended when stronger valve springs are used. Installation of these adaptors require adjustable pushrods.

Gaskets for S&S Float Bowls

O-Rings for S&S Accelerator Jets

O-Rings for S&S Accelerator Pump Cover

O-Rings for S&S Carburetors to Manifold and Insulator Block

S&S Breather Conversion Kits

Improved breather hardware to retrofit S&S Super E air cleaners. Advantages over the earlier system are in that the fittings and hoses plug on the cylinder head behind the backing plate and do not need to be removed for service on filter or carburetor. Coated washers are used instead of O-rings which are much more durable and seal better to prevent leaks.

O-Rings for S&S Float Valve

O-Rings for S&S Idle Adjuster Screw

Oil Seal for S&S Kicker Covers

S&S Pushrods for Panhead and Shovelhead

Stock replacement hydraulic pushrod kits. Include four adjustable steel pushrods. Stock adjusting screws which are not included must be used with these pushrods.

S&S Solid Lifter Kit for Shovelhead

Adjustable, solid pushrods in S&S quality made from chromoly steel for Shovelheads from 1966-1984. Complete kit with hardened solid lifter adaptors.

S&S Flywheel Assemblies

Complete pre-assembled flywheels with pinion shaft, sprocket shaft and connecting rods. Balanced and trued, ready to install. Pistons are not included, but any stock replacement pistons may be used. S&S flywheel assemblies are of the best quality money can buy and concerning stability and smooth running they easily meet new OEM parts and by far exceed all used flywheels.

S&S Pushrods for Evolution Big Twin

Adjustable pushrods from S&S to be used as replacement for the OEM non-adjustable counterparts. Precisely made from chrome-moly tubing. For hydraulic or solid lifters and a must if more performance is desired.

S&S Timesaver Pushrods for Evolution Big Twin

For all Big Twins 1984-up with hydraulic or solid lifters. The adjusting screw is much longer and 40% thicker compared to other adjustable pushrods. This allows quick removal and installation of pushrods without having to disassemble the rockerbox. This is a great advantage when changing the camshaft. Made from finest 7/16” chrome-moly tubing with hardened wear surfaces. The adjusting screws feature two milled flats to facilitate secure locking.

Counter Nuts for S&S Solid Lifter Kit

S&S Gaskets for Cylinder Head: Knucklehead 3-5/8 ” Bore

S&S Gaskets for Oil Return Lines on S&S Knucklehead Cylinder Heads

S&S Gaskets for Cylinder Base: Knucklehead 3-5/8 ” Bore

S&S Rebuild Kits for Oil Pumps: Pre-Twin Cam

S&S Gasket Kits for Rocker/Valve Spring Covers: KN Series Engines

Filter Element for S&S High-Flow Filter Kit

S&S Piston Ring Sets 3-5/8” Big Bore for Forged Pistons OHV 1936-1984

S&S Piston Ring Sets 3-5/8” Big Bore for Forged Piston Panhead/Shovelhead

S&S Gasket Kits for Oil Pumps: Pre-Twin Cam

S&S Filter Element for S&S Stealth Air Cleaner

Filter Element for S&S Induction System

S&S Gaskets for Cylinder Head: Panhead 3-5/8 ” Bore

S&S Rocker Housings

If you ever tried to locate the original counterparts on swap meets, you soon will like these very accurate and precise reproductions. Once installed you can hardly tell the difference.

S&S Super B Carburetors

The legendary Drag strip and salt lake world record carburetor. A must for all pure-tech aficionados! Conceived for Big Bore and Stroker engines, but yields more power for stock engines, too. The Easyriders Streamliner, the worlds fastest Harley (530 km/h), was equipped with S&S Super B carburetors. Comes without air cleaner and manifold which must be purchased separately.

S&S Super E Carburetor Kits

The S&S Super E and G carburetors are specifically designed for Harley-Davidson Big Twin and Sportster engines. They feature adjustable accelerator pump for instant throttle response at any rpm. The ejector nozzle is located in line between the main discharge tube and the butterfly for undisturbed air flow. With the rider in mind the idle mixture screw has been angled for greater accessibility even with 5 gal. gas tanks. The enrichment device also was refined with a large variable position lever attached to the air cleaner backplate where it is easy to operate even with thick gloves. The throttle spool assembly is designed for later style two cable pull open - pull closed throttle. Cables are not included and must be purchased separately. Following the tradition a teardrop shaped air cleaner has been retained but it was redesigned to reduce the installed lenght of the carb assembly. The new filter element has 19% more filtering area and combined with other design changes makes up to 14% more flow. S&S Super E & G are approximately 40 mm shorter than Super B carbs and provide easy clearance for Fat Bob tank applications and good rider comfort. The Super E carburetor has a 48 mm throat and is recommended for use on any Big Twin and Sportster engine with stock displacement or big bore/stroker lower ends, aftermarket exhaust systems and cams.

S&S Gaskets for Cylinder Base: Panhead and Shovelhead

S&S Rocker Arms and Shafts

Hard to find rocker arms and shafts remanufactured by S&S. These high quality rocker components are the same as S&S uses in the KN- Series engines, and will fit stock Knucklehead engines as well since they feature the the stock 1:1 rocker ratio. Each complete set comprises four rocker arms, rocker shafts, washers, spacers and special O-ring seals. The shafts are also available separately but are not compatible with stock rocker arms.

Intermediate Jets for S&S Super B, D, E and G

S&S Rocker Shafts

Replacement rocker arm shafts for all 1936–1947 Knucklehead engines. Can be combined with original and S&S aluminum valve spring covers. Sold as sets with four shafts.

S&S Super E Carburetor Only

The S&S Super E carburetors are specifically designed for Harley-Davidson Big Twin and Sportster engines. They feature adjustable accelerator pump for instant throttle response at any rpm. The ejector nozzle is located in line between the main discharge tube and the butterfly for undisturbed air flow. With the rider in mind the idle mixture screw has been angled for greater accessibility even with 5 gal. gas tanks. The enrichment device also was refined with a large variable position lever which is easy to operate even with thick gloves. The throttle spool assembly is designed for later style two cable pull open - pull closed throttle. Cables and air cleaner assembly are not included and must be purchased separately. S&S Super E are approximately 40 mm shorter than Super B carbs and provide easy clearance for Fat Bob tank applications and good rider comfort.

S&S Reducer Bushings

These inserts reduce the 1/2”-13 breather bolt thread to 5/16”-18, and come in helpful when you install later Evolution cylinder heads with ventilation to earlier engines with ventilation on the crankcase.

S&S Super E Carburetors Only - Black Series

S&S continues the success story of their Super E carbs with a special Black Series edition that was first released for the S&S 55th Anniversary in 2013. These carbs feature a distinctive gloss black Enduraguard coating, which is heat and chemical resistant. In addition to cool cosmetics the Big Bore versions have specially machined venturis for up to 7% more flow. The Black Series carbs are not offered as complete kits, but as carburetor only. That gives you complete freedom to work with these carbs in any custom application.

Main Jets for S&S Carburetors

S&S Gaskets for Cylinder Base: Shovelhead 3-5/8” Bore

S&S Gasket Kits for Rocker Covers: SH Series Engines

S&S Gaskets for Cylinder Head: Shovelhead 3-1/2 ” and 3-7/16 ” Bore

S&S Replacement Cylinder Heads P-Series

These cylinder heads are offered as replacements for the cylinder heads used in S&S P-Series engines. They come with valves and S&S .590” lift valve springs installed. Other than that they are bare.

S&S Gaskets for Cylinder Head: Shovelhead 3-5/8 ” Bore

Rebuild Kit for S&S L-Series Carburetors

Rebuild kit for S&S L-series carburetors (models GAL, MGAL, MGL y Early Style G, GA, F y FA). Each kit contains: throttle plate, throttle plate shaft, throttle plate bushings, return spring, as well as all necessary screws and gaskets.

Rebuild Kit for S&S Super B Carburetors

Master Rebuild Kits for S&S Super E and G

These ultimate carburetor repair kits comprise all the parts included with the regular Super E/G kits plus the parts of the accelerator pump repair kit. 1 throttle shaft with 2 throttle plate screws, 1 throttle plate, 2 lockwashers, 2 nuts, 1 throttle plate nylon washer, 1 throttle plate return spring, 1 pump actuator spring, 1 throttle plate O-ring, 1 bowl gasket, 4 bowl screws, 3 pump srews, 2 cable clamp screws, 1 ejector nozzle O-ring, 1 needle assembly, 1 accelerator pump bellows seal, 1 diaphragm, 1 diaphragm spring, 1 pump pushrod, 2 pump cover O-rings, 2 ball check, 1 ball check spring, 2 idle mixture screws, 1 idle mixture screw O-ring, 1 needle seat w/ fuel line elbow, 1 overflow hose, 1 plunger spring, 1 idle speed screw, 1 idle speed screw spring, 1 float pin, 1 VOES fitting cap,

Standard Rebuild Kits for S&S Super E and G

These standard rebuild kits for S&S Super E/G carburetor bodies include: 1 throttle shaft with 2 throttle plate screws, 1 throttle plate, 2 lockwashers, 2 nuts, 1 throttle plate nylon washer, 1 throttle plate return spring, 1 pump actuator spring, 1 O-ring insulator caburator , 1 bowl gasket, 1 O-ring ejector nozzle , 1 accelerator pump bellows seal, 1 O-ring idle mixture screw, 1 VOES- plug,

O-Rings for S&S Shovelhead Rocker Covers

Basic Rebuild Kit for S&S Super E and G

Basic repair kits which comprises all the gaskets and O-rings plus a new needle valve to overhaul your Super E/G carburetor. 1 throttle plate nylon washer, 1 throttle plate O-ring, 1 bowl gasket, 1 gasket carb-air cleaner, 1 ejector nozzle O-ring, 1 accelerator pump bellows seal, 1 diaphragm, 1 diaphragm spring, 2 pump cover O-rings, 1 ball check spring, 2 ball valves, 1 needle assembly, 1 overflow tube,

Rebuild Kit for S&S Super E and G Accelerator Pumps

This kit includes: 1 diaphragm, 1 diaphragm spring, 1 pump pushrod, 2 pump cover O-rings, 2 ball check, 1 ball check spring,

Swivel Fitting Fuel Line Kit S&S Super E and G

Upgrade your older S&S Super E or G carburetor with this 90° fuel inlet swivel fitting. It can be rotated a full 360 degrees so you can use common fuel lines without the usual space problems.

Replacement Parts for S&S Super B

S&S Super Stock Shovelhead Cylinder Heads

Primarily designed for stock replacement applications where traditional looks and improved performance are important. These cylinder heads are made from the same high-quality aircraft-cylinder head material like the Evolution heads. The intake port is the same diameter and is positioned in the same location as stock which means stock manifolds bolt right up. A directional vane like the one used in S&S Evo heads to route the air around the valve stem and guide area is located in the floor of the port. Standard intake valve diameter is stock at 1 15/16“. The combustion chamber is identical to stock enabling installation on any engine with hemispherical domed pistons. The exhaust port is also stock configuration and readily accepts stock style exhaust systems. Standard exhaust valve diameter is also stock at 1 3/4“. The pre-installed .590“ lift valve springs are used for greater cam lift versatility, the valve seats are compatible with present day unleaded fuel. Although these heads for Shovel big Twins are designed for stock replacement applications, flow characteristics have been improved up to 9% more flow. S&S Shovelhead cylinder heads easily bolt on and fit like stock. Frame and other clearancing problems are non-existent. Exhaust systems with stock dimensions can be used. Stock rocker cover assemblies are not included and are installed using hardware provided. Each High Output Super Stock Shovelhead cylinder head kit includes front and rear cylinder heads completely assembled with valve seats, valve guides, valves, valve springs, spring collars, valve keepers and valve guide seals ready to run. Also included are gaskets required for installation including cylinder base and head gaskets, rocker cover and exhaust port gaskets, rocker cover and exhaust pipe mounting hardware and installation instructions.

Shovelhead Top End Kits

Restore that tired iron! S&S has something for Shovelhead engines that are in need of a new top end. In a lot of cases it just isn’t worth it to try to rebuild the old, cracked, worn out cylinder heads or to bore the stock cylinders again. The S&S Shovelhead style top end kits provide everything you need to replace the top end of a 74“ or 80“ Shovelhead engine. They include pistons, rings, cylinders, cylinder heads, gaskets and hardware. Valves and springs are pre-installed and pistons are pre-fit to the cylinders, so there is no machine work to be done and very little down time. Kits for 74“ engines come with o-ring style cylinder heads, those for 80“ engines come with band style heads. Compression ratio for both top ends is 8:1. Since the kits are not interchangeable it is important to correctly identify the stroke of the engine before ordering.

Replacement Parts for S&S Super E and Super G Carburetors

S&S Rockerboxes

Just the fact that the S&S polished billet rocker covers for Shovelhead engines look so good may be reason enough to put them on your bike, but the beauty is not just skin deep. The well thought out design offers a number of advantages over conventional cast rocker boxes. Machined from billets of 356 aluminum, these rocker boxes provide the ultimate in stability and accuracy. The top and bottom sections of the covers are sealed with an o-ring type seal that insures leak free operation. Rocker shafts used in the S&S rocker boxes are a strong and economical straight design and anyone who has had to replace a set of stock shovelhead rocker shafts can tell you that this will save you money when it comes time to rebuild the top end. Clearanced for valve lifts of up to .590“.

S&S Gasket Kits for Cylinder Head and Base: V and T Series Engines

S&S Late to Early Pinion Shaft Conversion Kit

Big Twin Evo models from 1990–up, which are factory equipped with the one-piece flywheel and pinion shaft, require this pinion shaft conversion kit in conjuntion with S&S Sidewinder or Stroker Kits, because S&S flywheels are using the earlier system with the pinion shaft bolted to the flywheel. The kit contains the pinion gear, oil pump drive gear, pinion shaft spacer and pinion shaft nut.

S&S Gasket Kits for Rocker Covers: Evolution Engines

S&S Connecting Rod Kits

Complete High Performance connecting rod kits for O.H.V. Big Twins and Sportster. For stock and stroker engines. Each S&S kit contains reinforced rods, piston pin bushings, crank pin with two crank pin nuts and the connecting rod bearing set.

S&S Jetting Kit

This kit contains all jets to properly set up and jet all S&S carburetors. Parts are stored in labeled, durable vinyl divider boxes.

S&S High-Flow Filter Kit Super E and G

With larger and larger street engines becoming more common, S&S has developed a high flow air filter kit for Super E and G carburetors. The new filter is 1” wider than the standard filter and features a low restriction filter element. Combined with the larger surface area it adds an airflow increase of up to 37%! The filter and filter adapters extend the Teardrop housing by 1”, so the filter peeks out from under the Teardrop and imparts a high performance street racer look. Kit installs in minutes and includes pre-oiled filter element and three plated steel extensions.

S&S Roller Rocker Arms

Roller rocker arms that were designed for superior strength to eliminate the failure-prone stress areas and to reach higher rpm with reduced side thrusting. S&S roller rockers are forged from 4140 steel, heat-treated, and then shot-peened for additional strength and protection from fatigue. Rocker ratio is exactly 1,5:1. They feature 3/4” long bronze bushings which provide 50% more load bearing surface for improved longevity. Additional roller tip oiling can be achieved with S&S Quickee pushrods and lifter blocks. Each kit includes 2 front and rear rocker arms. Shafts have to be ordered separately, existing stock shafts can be retained.

S&S Gaskets for Cylinder Head: Evolution 3-5/8 ” Bore

S&S Gaskets for Cylinder Base: Evolution 4 ” Bore

S&S Gaskets for Cylinder Base: Evolution 3-5/8 ” Bore

S&S Gaskets for Cylinder Head: Evolution 4 ” Bore

S&S Rocker Arms Evolution and Twin Cam

If you are looking for something better than stock Evolution or Twin Cam style rocker arms, this is it! An economical solution for stock rebuilds, and mild performance upgrades. Forged from 4140 steel for greater strength than stock or cast steel rocker arms. In addition they feature the same .750“ long rocker shaft bushings as our S&S roller rockers do, for 50% more load bearing area than in stock and other aftermarket rocker arms. The valve contact tips are induction hardened for extended durability. Thousands of hours of engine testing have proved them to be superior to any non-roller rocker arm on the market. Recommended for cams of .585“ lift or less.

S&S Rocker Arm Shafts Evolution and Twin Cam

Seal Washers for S&S Rocker Cover Screws

S&S Gasket Kits for Rocker Covers: Twin Cam Engines

S&S Gasket Kits for Oil Pumps: Twin Cam

S&S Stroker Power T-Shirts

High quality 100% cotton fabric made T-shirts from the high performance company S&S Cycles. The left chest features an S&S logo and the back is adorned with a wild "Stroker Power" illustration.

S&S Strips T-Shirts

High quality 100% cotton fabric made T-shirts from the high performance company S&S Cycles. A classic 70's "Strips" design adorns the entire chest.

S&S Genuine Motor Parts T-Shirts

High quality 100% cotton fabric made T-shirts from the high performance company S&S Cycles. The left chest features an S&S logo and the back is adorned with a big "Genuine Motor Parts" logo.

S&S Going Fast T-Shirts

High quality 100% cotton fabric made T-shirts from the high performance company S&S Cycles. The left chest features a S&S logo and imprinted on the back there is a picture of S&S founder George Smith on his dual-carb knucklehead drag bike, Tramp I.

S&S Main Jet Tool

Special wrench with guide-pin for S&S main jets. Perfect for changing jets while carburetor remains installed on the engine.

S&S Degree Wheel Kit

The multipurpose degree wheel can be used to perform ignition timing, crankcase breather timing, cam degreeing etc.. The wheel is designed to adapt to the sprocket shaft of any Big Twin or Sportster by simply using the correct adapter provided. A must for every well equipped engine builder´s shop.

S&S Flywheel Fixing Brackets

Useful tools don’t have to be expensive. This handy bracket slides over the sprocket shaft splines of big twin engines, and bolts to one of the primary bolt holes of the crankcase to keep the crank from rotating. Like an extra set of hands while installing pistons and cylinders, or any other operation where you don’t want the crank to turn.

S&S Flywheel Balancing Scale Weights

Additional weights to increase the measuring range of the S&S balancing scales.

Individual Thrust Washers for Breather Valves

S&S Circuit Breaker and Generator Drive Gears

High quality circuit breaker and generator idler gears by S&S for generator Big Twin style engines.

S&S Pinion Gears for Sportster 1986-1987

Pinion gears in proven S&S quality. The color code is identical to the factory codes so they can be used as stock replacement. If the color code is unknown we recommend to order a gear in the middle size range. These sizes fit 9 out of 10 engines and provide adequate clearance under most circumstances. As a rule of thumb it is preferable to allow slightly more gear lash than too little.

Generator Style Gear Covers 8 Rib 1936-1953

Stock replacement gear covers for generator style OHV engines. They are machined to accept the stock ¼”-24 mounting screws with countersunk heads. The bushings for camshaft and pinion shaft are pre-installed and meet stock oiling system requirements. Every effort is made to ensure that these covers look as much like stock as possible which is so important in restoration applications.

Generator Style Gear Covers 4 Rib 1954-1962

Stock replacement gear covers for generator style OHV engines. They are machined to accept the stock ¼”-24 mounting screws with countersunk heads. The bushings for camshaft and pinion shaft are pre-installed and meet stock oiling system requirements. Every effort is made to ensure that these covers look as much like stock as possible which is so important in restoration applications.

S&S Compression Release Socket Kit

Special S&S two-piece compression release socket kit which allows in-frame installation of S&S compression releases and protects wiring from damage.

S&S Gear Covers

Gearcovers for alternator style Big Twins. In spite of the simple, elegant design, these gearcovers are tough as nails. Machined from a solid aluminum billet, they are extremely strong and are dimensionally more precise than is possible with a cast part. The finish is flawless, show quality polished aluminum. Available For 1973-1992 and 1993-1999 Style Engines. The latter should only be used with engines that have the crankcase breather routed through the cylinder heads.

S&S Tappet Block Alignment Tool

This tapered tool for Evo Big Twins aligns tappet guide to engine case so tappet rollers run straight on the cam lobes.

Complete oil pump assemblies to solve oil supply problems on OHV Big Twin engines 1936-up except Twin Cam models. Can be used to update bikes with earlier cast iron pumps or as a direct replacement on later models with aluminum pumps. The pump body is CNC machined from billet aluminum which enhances the overall appearance of any engine. Compared to 1936-67 pumps the S&S product delivers 33% more oil. For maximum versatility they feature various fittings to either duplicate the original oil line routing or tailor one to suit custom requirements. Installations on engines from 1936–69 are strictly bolt-on if running solid lifters, also engines 1981-up require no modifications. Other crankcase year groups require a simple drilling or plugging step. For this purpose a special metal drill jig is required and available.

S&S High Volume High Pressure Oil Pump Evolution

The S&S High Volume High Pressure (HVHP) billet oil pump is a high capacity pump that was designed for the S&S Super Sidewinder Plus Engines. The SSW+ engines feature piston cooling jets that spray oil on the underside of the pistons. In order to supply enough oil for the cooling jets in addition to the oil requirements of the rest of the engine, a more efficient pump was needed. Although the HVHP oil pumps are very similar in appearance to the standard S&S billet pumps, there are several important differences. Special design features: A new tooth profile with fewer, but larger teeth, provides increased oil volume for both supply and return sides of the pump., Supply gears are 9% wider than stock or standard S&S oil pumps to give the HVHP pump even more oil capacity., Return gears are 28% wider than stock or standard S&S pumps to insure that the additional volume of oil supplied to the engine is scavenged and returned to the oil tank, preventing oil carry over from the crankcase breather., In spite of wider supply and return gears, the HVHP pump is no thicker than stock and uses the stock oil pump drive shaft. , The universal cover has a number of oil feed and return options allowing maximum flexibility for customized installations., Each pump includes supply and return gears, drive shaft, snap rings, miscellaneous hose fittings, gaskets and mounting hardware.,

Drilling Jig for S&S Oil Pumps

S&S Sockets for Main Shaft and Counter Shaft Bearings

Indispensable tool for disassembly and assembly of S&S 5- and 6-speed transmissions. Special socket for the internal hex ring nuts, that hold the support bearings in the access door.

Breather Valve for S&S Oil Pump

S&S Crankcase Breather Valve for Twin Cam

Since production start, there have been Twin Cam A engines that have had oil carry over problems, more commonly known as ”oil out the breather“. This is caused by pressure changes in the crankcases as the pistons travel up and down which prevent the oil from the cylinder heads to drain down into the cam chest. Instead oil is trapped in the drain passage. When enough oil accumulates in the rocker boxes, it will start to blow out of the crankcase breather. The problem is generally more common at sustained high speeds, and is also more common in big inch engines. For years, it was something you sometimes just had to live with. The S&S Crankcase Breather Valve for Twin Cams is an effective and economical solution to these oil carry-over problems in Twin Cams.➻It achieves an improved pressure balance for free oil flow. You can even expect a slight increase in midrange horsepower. Installation is easy and best performed when changing cams or servicing oil pump.

Crank position sensor by S&S; for crank position; fits Big Twin 1984-2007; S&S I.S.T.; with 120 cm long wiring harness; USA; gross weight: 73 g

Ignition coil by S&S; fits Softail 2000-2006, Dyna 1999-2005, FLT 2002-2006, Sportster 2004-2006; with carburetor; black; use with 12 V; primary resistance: 2 x 0.8 Ω; single fire - single plug; high tens. tower(s): two; replaces OEM HD 31655-99; gross weight: 700 g

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.000 ”; nominal bore: 3-7/16 ”; gross weight: 1.28 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.010 ”; nominal bore: 3-7/16 ”; gross weight: 1.3 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.020 ”; nominal bore: 3-7/16 ”; gross weight: 1.23 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.030 ”; nominal bore: 3-7/16 ”; gross weight: 1.3 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.040 ”; nominal bore: 3-7/16 ”; gross weight: 1.31 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.050 ”; nominal bore: 3-7/16 ”; gross weight: 1.32 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.060 ”; nominal bore: 3-7/16 ”; gross weight: 1.35 kg

Forged piston by S&S; for 4-1/2", 4-5/8" and 4-3/4" stroker kits; fits Knucklehead, Panhead and Shovelhead; aluminum forged; Over-/Undersize: +0.070 ”; nominal bore: 3-7/16 ”; gross weight: 1.36 kg

Cast piston by S&S; for front and rear cylinder; fits Evolution stroker kits; cast aluminum; Over-/Undersize: +0.000 ”; stroke: 4-5/8 ”; nominal bore: 3-1/2 ”; 89 in³; compression: 10:1; with piston rings, pins and clips; gross weight: 1.11 kg

Cast piston by S&S; for front and rear cylinder; fits Evolution stroker kits; cast aluminum; Over-/Undersize: +0.030 ”; stroke: 4-5/8 ”; nominal bore: 3-1/2 ”; 89 in³; compression: 10:1; with piston rings, pins and clips; gross weight: 1.13 kg

Crankcases »Super Stock« by S&S; fits Big Twin 1970-1984; Stock Bore; cast aluminum, bare; alternator style; nominal bore: 3-1/2 ”; with bearings 63-032 and 63-051 and small parts; gross weight: 14.6 kg

Forged piston by S&S; for front and rear cylinder; fits Twin Cam Stroker kits; aluminum forged; Over-/Undersize: +0.005 ”; stroke: 4-1/2 ”; nominal bore: 3-7/8 ”; 106 in³; compression: 10,1:1; with piston rings, pins and clips; gross weight: 1.36 kg

Crankcases »Super Stock« by S&S; fits Big Twin 1970-1984; Big Bore; cast aluminum, bare; alternator style; nominal bore: 3-5/8 ”; with bearings 63-032 and 63-051 and small parts; gross weight: 13.6 kg

Forged piston by S&S; for front and rear cylinder; fits Twin Cam Stroker kits; aluminum forged; Over-/Undersize: +0.010 ”; stroke: 4-1/2 ”; nominal bore: 3-7/8 ”; 106 in³; compression: 10,1:1; with piston rings, pins and clips; gross weight: 1.3 kg

Crankcases »Super Stock« by S&S; fits Big Twin 1984-1991; Stock Bore; cast aluminum, bare; alternator style; nominal bore: 3-1/2 ”; with bearings 63-032 and 63-051 and small parts, crank position sensor hole drilled; gross weight: 15.2 kg

Crankcases »Super Stock« by S&S; fits Big Twin 1992-1999; Stock Bore; cast aluminum, bare; alternator style; nominal bore: 3-1/2 ”; with bearings 63-032 and 63-051 and small parts, crank position sensor hole drilled; gross weight: 14.7 kg

Crankcases »Super Stock« by S&S; fits Big Twin 1992-1999; Stock Bore; cast aluminum, black; alternator style; nominal bore: 3-1/2 ”; with bearings 63-032 and 63-051 and small parts, crank position sensor hole drilled; gross weight: 14 kg

O-Ring by S&S; for Manifold clamps; fits Big Twin 1955-1978, Sportster 1957-early 1978; also used on: starter engine solenoid Big Twin 1980–84; Viton; ID x OD: 40.9 x 51.2 mm, 5.3 mm thick; replaces OEM HD 27060-55; gross weight: 10 g

Bearing race by S&S; for main-shaft support; fits Big Twin 1985-2005 (Softail, Touring →2006); steel; length: 30.35 mm; outer Ø: 32.15 mm; inner; replaces OEM HD 34091-85; gross weight: 90 g

Manifold »O-Ring Type« by S&S; for Super B and E / 93” Sidewinder Kit; fits Shovelhead; cast aluminum, tumble polished; for S&S carburetors; gross weight: 200 g

Manifold »O-Ring Type« by S&S; for Super B and E / 96” Sidewinder Kit; fits Shovelhead; cast aluminum, tumble polished; for S&S carburetors; gross weight: 210 g

Manifold »Rubberband Type« by S&S; for Super G / 98” Sidewinder Kit; fits Shovelhead; cast aluminum, tumble polished; for S&S carburetors; gross weight: 250 g

Cam shafts »570 GP« by S&S; for S&S oil pump; fits Twin Cam 1999-2006 (exc. Dyna 2006); steel; valve lift (IN/EX): 14.48/14.48 mm; gross weight: 2.1 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 125; pitch: 14 mm; gross weight: 900 g

Cam shafts »585 GP« by S&S; for S&S oil pump; fits Twin Cam 1999-2006 (exc. Dyna 2006); steel; valve lift (IN/EX): 14.86/14.86 mm; gross weight: 2.06 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 128; pitch: 14 mm; gross weight: 820 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 130; pitch: 14 mm; gross weight: 850 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 132; pitch: 14 mm; gross weight: 820 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 133; pitch: 14 mm; gross weight: 830 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 135; pitch: 14 mm; gross weight: 920 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/8”; number of teeth: 139; pitch: 14 mm; gross weight: 920 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 126; pitch: 14 mm; gross weight: 980 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 127; pitch: 14 mm; gross weight: 1.05 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 128; pitch: 14 mm; gross weight: 970 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 130; pitch: 14 mm; gross weight: 1 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 132; pitch: 14 mm; gross weight: 980 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 133; pitch: 14 mm; gross weight: 940 g

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 135; pitch: 14 mm; gross weight: 1.16 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 136; pitch: 14 mm; gross weight: 1 kg

Secondary belt by S&S; polyurethane / X3N carbon cord; width: 1-1/2”; number of teeth: 139; pitch: 14 mm; gross weight: 1.1 kg

Adapter by S&S; for Solid lifter kit; steel, IH = 8,5 mm; gross weight: 50 g

O-Ring by S&S; for Accelerator jet; S&S Super E/G carburetors; fluoroelastomer; ID x OD: 2.9 x 6.5 mm, 1.8 mm thick ; inner Ø: 3.1 mm; gross weight: 1 g

O-Ring by S&S; for Idle adjuster screw; S&S Super E/G carburetors; fluoroelastomer; ID x OD: 3 x 5 mm, 1 mm thick ; inner Ø: 3 mm; gross weight: 1 g

O-Ring by S&S; for Cover / Accelerator pump; S&S Super E/G carburetors; fluoroelastomer; ID x OD: 5.2 x 9 mm, 1.9 mm thick ; inner Ø: 5.4 mm; gross weight: 1 g

O-Ring by S&S; for Rocker cover; fits Big Twin 1966-1984; between top and base cover, front cylinder head; fluoroelastomer; ID x OD: 9.7 x 11.7 mm, 1 mm thick; gross weight: 1 g

O-Ring by S&S; for Float valve; S&S Super E/G carburetors; fluoroelastomer; ID x OD: 10 x 13 mm, 1.5 mm thick ; gross weight: 1 g

O-Ring by S&S; for Rocker cover; fits Big Twin 1966-1984; between top and base cover, rear cylinder head; fluoroelastomer; ID x OD: 11 x 13 mm, 1 mm thick; gross weight: 1 g

Needle bearing by S&S; for Tappet; fits models 1930-1984 (Sportster →1985); steel; width: 9.5 mm; ID x OD: 5.4 x 21.7 mm; tolerance class: ABEC 1; replaces OEM HD 18534-29; gross weight: 120 g

Needle bearing by S&S; for Tappet; fits Evolution models; steel; width: 9.5 mm; ID x OD: 5.4 x 24 mm; tolerance class: ABEC 1; gross weight: 140 g

Hydraulic unit by S&S; fits Big Twin 1953-1984; steel; replaces OEM HD 17920-53A; gross weight: 70 g

O-Ring by S&S; for Rocker cover; fits Big Twin 1966-1984; rocker arm shaft screws; fluoroelastomer; ID x OD: 20.2 x 24 mm, 1.9 mm thick; gross weight: 1 g

Drain plug by S&S; for S&S Super Stock crankcases 05/2000→; steel, zinc plated, magnetic; socket head; thread: 1/2”-20; wrench size: 1/4 ”; with O-ring; gross weight: 10 g

Filter element by S&S; for Air cleaner; for S&S Super B; foam rubber; depth: 60 cm; inner Ø: 120 mm; outer Ø: 160 mm; gross weight: 110 g

Filter element by S&S; for Air cleaner; for S&S Super E/G; rubber / cotton / steel, K&N type; depth: 65 mm; inner Ø: 125 mm; outer Ø: 158 mm; gross weight: 100 g

Crank pin by S&S; fits Big Twin 1981-1998 (Softail →1999); steel; replaces OEM HD 23961-80A; gross weight: 640 g

Nut by S&S; for Crank pin; fits Big Twin 1981-1999; steel, parkerized, high profile; wrench size: 1-1/2 ”; thread: 1”-20; replaces OEM HD 23969-80, and 23969-83; gross weight: 50 g

Pinion shaft by S&S; fits OHV Big Twin 1939-1953; steel; replaces OEM HD 24007-39; gross weight: 430 g

Pinion shaft by S&S; fits Big Twin 1958-early 1981; steel; with →1972 and 1973→ end plugs; replaces OEM HD 24006-58; gross weight: 520 g

Pinion shaft by S&S; for S&S flywheels →1999; fits Big Twin late 1981-1986; steel; replaces OEM HD 24006-80; gross weight: 520 g

Sprocket shaft by S&S; fits SV + OHV Big Twin 1930-1954; with nuts and keys; steel, thread sprocket and shaft nut (flywheel side): 3/4”-20; replaces OEM HD 24001-30; gross weight: 510 g

Sprocket shaft by S&S; fits Big Twin 1955-1964 with S&S flywheels; steel; with key and nut; gross weight: 730 g

Sprocket shaft by S&S; fits Big Twin 1965-1969 with S&S flywheels; steel; with key and nut; gross weight: 800 g

Sprocket shaft by S&S; fits Big Twin 1970-1999 with S&S flywheels; steel; with key and nut; gross weight: 820 g

Nut by S&S; for Pinion shaft / Sprocket shaft; for S&S flywheels; steel, parkerized; wrench size: 1-1/4 ”; gross weight: 30 g

Woodruff key by S&S; for Crank pin; fits models 1918-1981; steel; L x W x H: 12.37 x 3.2 x 4.83 mm; replaces OEM HD 23985-18; gross weight: 10 g

Cylinder head »Super Stock« by S&S; fits Shovelhead 1966-1978; cast aluminum / steel / spring steel; nominal bore: 3-7/16 ” / 3-1/2 ”; exhaust flanges G: Shovelhead; head bolt pattern: Shovelhead; intake manifold flanges: Shovelhead, O-ring type (1966-1978); oil supply: external; plug threads: 1 x M14 x 1.25 x 19 mm; gross weight: 11.84 kg

Woodruff key by S&S; for Crank pin / Pinion shaft; fits all 1981-1998 (Sportster, Softail →1999); steel; L x W x H: 9.3 x 3.2 x 4.33 mm; replaces OEM HD 11218; gross weight: 10 g

Cylinder head »Super Stock« by S&S; fits Shovelhead 1979-1984; cast aluminum / steel / spring steel; nominal bore: 3-7/16 ” / 3-1/2 ”; exhaust flanges G: Shovelhead; head bolt pattern: Shovelhead; intake manifold flanges: Shovelhead, rubberband type (1979-1984); oil supply: external; plug threads: 1 x M14 x 1.25 x 19 mm; gross weight: 11.64 kg

Top end kit by S&S; fits Shovelhead 1966-1978 (1200 ccm); cast aluminum / cast iron / steel / aluminum; stroke: 3-31/32 ”; compression: 8:1; exhaust flanges G: Shovelhead; head bolt pattern: Shovelhead; intake manifold flanges: Shovelhead, O-ring type (1966-1978); oil supply: external; plug threads: 1 x M14 x 1.25 x 19 mm; gross weight: 28 kg

Top end kit by S&S; fits Shovelhead 1979-1984 (1340 ccm); cast aluminum / cast iron / steel / aluminum; stroke: 4-1/4 ”; compression: 8:1; exhaust flanges G: Shovelhead; head bolt pattern: Shovelhead; intake manifold flanges: Shovelhead, rubberband type (1979-1984); oil supply: external; plug threads: 1 x M14 x 1.25 x 19 mm; gross weight: 28 kg

Enrichment device »Super B type« by S&S; for S&S Carbs; stainless steel / brass, 1 stage; gross weight: 30 g

Connecting rod bearing set by S&S; for con-rod big end; fits Big Twin 1941-1999; steel retainers; steel; with standard rollers; replaces OEM HD 24385-40B; USA; gross weight: 130 g

Bearing retainer by S&S; for Connecting rods; fits Big Twin 1941-1999; aluminum; replaces OEM HD 24366-71, and 24367-71; gross weight: 30 g

Gasket »Firering« by S&S; for Cylinder head; fits Twin Cam 88 and 96; metal/graphite compound; nominal bore: 3-3/4 ”; thickness: 0.046 ”; replaces OEM HD 16775-99; gross weight: 30 g

Nut by S&S; for Pinion gear; fits Big Twin 1954-1989; steel; thread: 5/8”-24 LH; replaces OEM HD 24023-54; gross weight: 20 g

Spacer by S&S; for Pinion gear; fits Big Twin 1954-1989; steel; replaces OEM HD 24703-54B; gross weight: 10 g

Drive gear by S&S; for Oil pump; fits Big Twin OHV 1939-1953; on pinion shaft; steel, 6 teeth; replaces OEM HD 26349-39; gross weight: 50 g

Drive gear by S&S; for Oil pump; fits Big Twin 1973-1984; on pinion shaft; steel, 6 teeth; replaces OEM HD 26349-73A; gross weight: 50 g

Thrust washer by S&S; for Breather valve; fits Big Twin late 1979→; steel, .100”, .110”, .120”, .130”, .140”, .150”, .160”, .170”.; 8 pieces; gross weight: 50 g

Drive gear by S&S; for Oil pump; fits Big Twin 1973-1998 (Softail →1999); steel, 24 teeth; replaces OEM HD 26345-73; gross weight: 80 g

Gear by S&S; for Oil pump; fits Big Twin 1968→; drive, oil return; steel; replaces OEM HD 26315-68A; USA; gross weight: 40 g

Gear by S&S; for Oil pump; fits Big Twin 1968→; idler, oil return; steel; replaces OEM HD 26317-68A; USA; gross weight: 40 g

Gear by S&S; for Oil pump; fits Big Twin 1968→; drive, oil feed ; steel; replaces OEM HD 26328-74; USA; gross weight: 40 g

Gear by S&S; for Oil pump; fits Big Twin 1968→; idler, oil feed; steel; replaces OEM HD 26326-62A; USA; gross weight: 40 g

Spring by S&S; for relief valve; fits Big Twin 1973-1998 (Softail →1999); spring steel; length: 59 mm; replaces OEM HD 26207-83; gross weight: 30 g